manualshive.com logo in svg

Motorola Symbol DS3407, Reference Manual

Share
Download
Motorola Symbol DS3407 Reference Manual Download Page 150

10 - 2 Symbol DS3407 Product Reference Guide

Errors While Scanning

Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the correct parameter.

Symbology Parameter Defaults

Table 10-1

 lists the defaults for all symbologies parameters. There are two ways to change the default values:

•

Scan the appropriate bar codes in this guide. These new values replace the standard default values in 
memory. To recall the default parameter values, scan 

*Restore Defaults on page 4-4

.

•

Download data through the device’s serial port using SSI. Hexadecimal parameter numbers appear in this 
chapter below the parameter title, and options appear in parenthesis beneath the accompanying bar codes. 
Refer to the 

Simple Serial Interface (SSI) Programmer’s Guide 

for detailed instructions for changing 

parameters using this method.

NOTE

See 

Appendix A, Standard Default Parameters

 for all user preferences, hosts, and miscellaneous default 

parameters.

Table 10-1    

Symbology Default Table

Parameter

Parameter 

Number

Default

Page 

Number

UPC/EAN

UPC-A

01h

Enable

10-7

UPC-E

02h

Enable

10-7

UPC-E1

0Ch

Disable

10-8

EAN-8/JAN 8

04h

Enable

10-8

EAN-13/JAN 13

03h

Enable

10-9

Bookland EAN

53h

Disable

10-9

Decode UPC/EAN/JAN Supplementals 
(2 and 5 digits)

10h

Ignore

10-10

User-Programmable Supplementals

Supplemental 1: 

Supplemental 2: 

F1h 43h

F1h 44h

10-13

UPC/EAN/JAN Supplemental Redundancy

50h

10

10-13

Transmit UPC-A Check Digit

28h

Enable

10-14

Transmit UPC-E Check Digit 

29h

Enable

10-14

Transmit UPC-E1 Check Digit

2Ah

Enable

10-15

UPC-A Preamble

22h

System Character

10-15

UPC-E Preamble

23h

System Character

10-16

Summary of Contents for Symbol DS3407





















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands