Motorola NVG510 Administrator'S Handbook Download Page 22 | Manualshive

Page: 22 / 152

background image

Administrator’s Handbook

22

The Device Status displays the following information in the center section:

Some fields may or may not display, depending on your particular setup.

The

Diagnostics

button will connect you to the

Troubleshoot

page. See

“Diagnostics” on page 61

.

The right-hand frame displays some links to commonly
performed tasks for easy access.

◆

Go to AT&T online support for troubleshooting and repair

»

This link will connect you to the

IP Diagnostics

page with help for troubleshooting and the AT&T Help Desk

information. See

“IP Diagnostics page” on page 20

.

◆

Modify your Wireless security or settings

»

This link will connect you to the

Wireless

page. See

“Wireless” on page 35

.

◆

Restart your gateway

»

This link will connect you to the

Restart Device

page. See

“Restart Device” on page 27

.

◆

Find a computer on your home network

»

This link will connect you to the

Device List

page. See

“Device List” on page 24

.

◆

Adjust firewall settings for gaming and applications

»

This link will connect you to the

NAT/Gaming

page. See

“NAT/Gaming” on page 53

.

Field

Description

Broadband

Broadband Connection

‘Waiting for DSL’ is displayed while the Gateway is training. This
should change to ‘Up’ within two minutes.
‘Up’ is displayed when the ADSL line is synched and the PPPoE ses-
sion is established.
‘Down’ indicates inability to establish a connection; possible line fail-
ure.

Line State

Line State connection (Internet) is either Up or Down

Wi-Fi

Status

Your wireless signal may be ‘On’ or ‘Off’.

Network ID (SSID)

This is the name or ID that is displayed to a client scan. The default
SSID for the Gateway is

attxxx

where

xxx

is the last 3 digits of the

serial number located on the side of the Gateway.

Authentication Type

The type of wireless encryption security in use. May be

Disabled

,

WPA

or

WEP

,

Default Key

or

Manual

.

Network Key

Wireless network encryption key in use.

Voice

Line 1

Indication of VoIP or other phone connection.

Line 2

Indication of VoIP or other phone connection.

«
...
20
21
22
23
24
...
»

Summary of Contents for NVG510

























































































































































Reviews:

No comments

Related manuals for NVG510

Brand: Pathport Pages: 3

Subnet16 BIS Z-GW-001-IND

Brand: Balluff Pages: 2

Brand: OleumTech Pages: 104

VGW VIRTUAL GATEWAY

Brand: Juniper Pages: 6

MSR3610-I Series

Brand: H3C Pages: 33

Brand: Dusun Pages: 8

Brand: Badger Meter Pages: 24

SURFBOARD SBG1000

Brand: Motorola Pages: 8

SURFBOARD SBG1000

Brand: Motorola Pages: 16

Brand: Motorola Pages: 9

SURFboard SVG7782

Brand: Motorola Pages: 40

SURFBOARD SBG1000

Brand: Motorola Pages: 2

VT2442 - VONAGE

Brand: Motorola Pages: 12

Brand: Motorola Pages: 2

Brand: Motorola Pages: 15

Brand: Motorola Pages: 2

Brand: Motorola Pages: 84

SURFboard 574823-001-a

Brand: Motorola Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands