manualshive.com logo in svg

Motorola NVG510, Administrator'S Handbook

Share
Download
Motorola NVG510 Administrator'S Handbook Download Page 71

71

Motorola® Gateway NVG510 Rear View

Service

Solid Green

 = IP connected (The device has a WAN IP address from DHCP or 802.1x 

authentication and the broadband connection is 
up).                                                                                                

Flashing Green

 = Attempting PPP connection.  Attempting IEEE 802.1X authentication or 

attempting to obtain DHCP information.

Red

 = Device attempted to become IP connected and failed (no DHCP response, no PPPoE 

response, 802.1x authentication failed, no IP address from IPCP, etc.). The Red state times 
out after two minutes and the Service indicator light returns to the Off state. 
Off = The device is not powered or the broadband connection is not present.

Phone 1, 2

Solid Green

 = The associated VoIP line has been registered with a SIP proxy server.

Flashing Green

 = Indicates a telephone is off-hook on the associated VoIP line.

Off = VoIP not in use, line not registered or Gateway power off.

LED

Action

Factory Reset Switch

DC Power Port

WPS Pushbutton

Ethernet Ports

Phone Port

(use splitter for

2 phones)

DSL Port

Summary of Contents for NVG510

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands