manualshive.com logo in svg

Motorola NVG510, Administrator'S Handbook

Share
Download
Motorola NVG510 Administrator'S Handbook Download Page 86

Administrator’s Handbook

86

show all-info

Displays all settings currently configured in the Motorola Gateway.

show bridge interfaces

Displays bridge interfaces maintained by the Motorola Gateway.

show bridge table

Displays the bridging table maintained by the Motorola Gateway.

show config

Dumps the Motorola Gateway’s configuration script just as the 

script

 command does in config mode.

show crash

Displays the most recent crash information, if any, for your Motorola Gateway.

show daylight-savings

Displays the auto-daylight savings time settings information.

show dhcp agent

Displays DHCP relay-agent leases.

show dhcp server leases

Displays the DHCP leases stored in RAM by your Motorola Gateway.

show diffserv

Displays the Differentiated Services and QoS values configured in the Motorola Gateway.

show dslf device-association

Displays LAN devices that conform with the TR111 Gateway requirement. It displays - IP Address, Manufacture 
OUI and Serial number.

show enet [ all ]

Displays Ethernet interface statistics maintained by the Motorola Gateway. Supports display of individual LAN 
switch port statistics as well as WAN Ethernet statistics (where applicable).

Example:

Ethernet driver full statistics - 10/100 Ethernet

Port Status:  Link up

Type: 100BASET  Duplex: Full

General:

 Transmit OK           : 434

 Receive OK            : 267

Summary of Contents for NVG510

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands