Motorola DSP56303 User Manual Download | Manualshive

Page: 181 / 320

background image

ESSI Programming Model

Enhanced Synchronous Serial Interface (ESSI)

7

-33

7.5.7

ESSI Transmit Data Registers (TX[2–0])

ESSI0:TX20, TX10, TX00; ESSI1:TX21, TX11, TX01

TX2, TX1, and TX0 are 24-bit write-only registers. Data written into these registers
automatically transfers to the transmit shift registers. (See Figure 7-12 and Figure 7-13.) The
data transmitted (8, 12, 16, or 24 bits) is aligned according to the value of the ALC bit. When
the ALC bit is cleared, the MSB is Bit 23. When ALC is set, the MSB is Bit 15. If the transmit
data register empty interrupt has been enabled, the DSP is interrupted whenever a transmit
data register becomes empty.

Note:

When data is written to a peripheral device, there is a two-cycle pipeline delay
while any status bits affected by this operation are updated. If any of those status
bits are read during the two-cycle delay, the status bit may not reflect the current
status.

7.5.8

ESSI Time Slot Register (TSR)

TSR is effectively a write-only null data register that prevents data transmission in the current
transmit time slot. For timing purposes, TSR is a write-only register that behaves as an
alternative transmit data register, except that, rather than transmitting data, the transmit data
signals of all the enabled transmitters are in the high-impedance state for the current time slot.

7.5.9

Transmit Slot Mask Registers (TSMA, TSMB)

Both transmit slot mask registers are read/write registers. When the TSMA or TSMB is read
to the internal data bus, the register contents occupy the two low-order bytes of the data bus,
and the high-order byte is filled by 0. In Network mode the transmitter(s) use these registers
to determine which action to take in the current transmission slot. Depending on the bit
settings, the transmitter(s) either tri-state the transmitter(s) data signal(s) or transmit a data
word and generate a transmitter empty condition.

23

22

21

20

19

18

17

16

15

14

13

12

TS15

TS14

TS13

TS12

11

10

9

8

7

6

5

4

3

2

1

0

TS11

TS10

TS9

TS8

TS7

TS6

TS5

TS4

TS3

TS2

TS1

TS0

—Reserved bit; read as 0; write to 0 0 for future compatibility.

(ESSI0 X:$FFFFB4, ESSI1 X:$FFFFA4)

Figure 7-14. ESSI Transmit Slot Mask Register A (TSMA)

«
...
179
180
181
182
183
...
»

Summary of Contents for DSP56303

































































































































































































































































































































Reviews:

No comments

Related manuals for DSP56303

Brand: Vdwall Pages: 29

Brand: Heinner Pages: 37

Brand: Dualit Pages: 14

Brand: JD Williams and Co Pages: 6

Brand: Marta Pages: 26

Brand: EVS Pages: 30

Brand: Nutri Ninja Pages: 16

Brand: Audiotec Fischer Pages: 20

Masterchef Compact

Brand: Moulinex Pages: 116

Brand: Chicco De'Longhi Pages: 27

Brand: Overmax Home Pages: 27

Brand: HAMILTON BEACH/PROCTOR SILEX Pages: 13

Brand: Hamilton Beach Pages: 44

Brand: Garland Pages: 156

Brand: Unika Pages: 40

Brand: Vega Pages: 60

Brand: Bosch Pages: 56

Brand: Bosch Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands