Motorola DCT1800 Installation Manual Download Page 39 | Manualshive

Page: 39 / 53

background image

B-12

Diagnostics

DCT1800 Installation Manual

Field Description

Multicast 16 Address

The Multicast 16 address numbers change to display the values for each data
stream. The following is a list of Multicast 16 addresses:

!

NET

!

EMM

!

SCC

!

DWLD

!

DATA

!

VCN

!

POLL

Seed Health

This value represents the health of the set-top and should be 0xFF. If it is not
0xFF, see the “Troubleshooting” section for more information.

d 06: Firmware Version

The FIRMWARE VERSION diagnostic displays the:

!

Dena firmware version or revision number

!

Build date and time

!

TSODA firmware version number

!

CAMEL (CMLBK) firmware version number (always 0000)

The BOOT is the lowest level of firmware code that can be used on the DCT1800.

Figure B-7
Firmware Version

06

FIRMWARE VERSION

07.72

BOOT 07.71

Sep 13, 2002

10:40:21

TSODA t16

CMLBK 0000

«
...
37
38
39
40
41
...
»

Summary of Contents for DCT1800






















































Reviews:

No comments

Related manuals for DCT1800

Brand: NAD Pages: 2

Brand: LaserLiner Pages: 40

Brand: LabSat Pages: 2

Brand: Yamaha Pages: 99

Brand: Yamaha Pages: 74

V665 - RX AV Receiver

Brand: Yamaha Pages: 2

XDOM RPL - PRODUCTSHEET

Brand: Ebode Pages: 24

Brand: Harman Kardon Pages: 28

Brand: UNIBOX Pages: 59

Brand: R.L.DRAKE Pages: 46

SOUND SYSTEM 1.0

Brand: Seat Pages: 124

Brand: Aiwa Pages: 16

Brand: Conrad Pages: 49

Brand: Yaesu Pages: 15

Brand: Harman Kardon Pages: 12

Brand: Future light Pages: 31

Brand: Dynascan Pages: 10

Brand: PCB Piezotronics Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands