Motorola DCT1800 Installation Manual Download Page 49

Page: 49 / 53

B-22

Diagnostics

DCT1800 Installation Manual

Table B-15
MAC Frequency Table Fields

Field Description

Frequency

Indicates the frequency, in Hz, for an upstream channel.

Power

Indicates the power level, in dBmV, used on a particular upstream channel to send
data to the RPD.

d 14: Message Types

This diagnostic displays a listing of PIDs and counts. In addition the message types with IDs
and counts are shown:

Figure B-15
Message Types

14 MESSAGE TYPES (hex data)

OOB:

INB:

PID

Cnt

PID

Cnt

Lost DRAM

0000

0 0

0000

0 0

Msg

Id Cnt Msg Id Cnt

216 9A E 0

2 89 A0 15

Table B-16
Message Types Fields

Field Description

OOB PID

Indicates out-of-band PID.

OOB Cnt

Indicates the number of messages received.

INB PID

Indicates the in-band PID.

INB Cnt

Indicates the number of messages received.

INB Lost

Indicates the number of messages lost due to errors.

DRAM

Indicates the count of in-band ring buffer overflows.

MSG

Indicates the message type.

Indicates the low order byte of the Connection ID.

Cnt

Indicates the number of messages received.

Summary of Contents for DCT1800






















































Search results

Summary of Contents for DCT1800

Reviews:

Related manuals for DCT1800

Brands by name

Popular brands

Motorola DCT1800, Installation Manual

Search results

Summary of Contents for DCT1800

Reviews:

Related manuals for DCT1800

Brands by name

Popular brands