Motorola DCT1800 Installation Manual Download Page 43

Page: 43 / 53

B-16

Diagnostics

DCT1800 Installation Manual

d 08: Renewable Security System

The renewable security system includes a TVPC card that returns the security status to current.

Figure B-9
Renewable Security

RENEWABLE SECURITY

TVPC NOT REQUIRED

CRYPTO

NOT MATED

STATUS

VERSION

Table B-10
Renewable Security Fields

Field Description

TVPC Required / Not Required

Indicates whether further operation of the set-top requires the TVPC.

CRYPTO

Lists the current mode as displayed on the CRYPTO OSD ( Stand Alone,
Support, or Not Mated).

Status

Indicates the TVPC status with the following variables:

TVPC communication problem

TVPC required

Validator does not match between GK and TVPC

Invalid unit key number

Old TVPC unit address

TVPC not mated

TVPC /base module unit address mismatch

New TVPC, but wrong version number

TVPC unit address mismatch

Version

Indicates the version of renewable security being used.

Summary of Contents for DCT1800






















































Search results

Summary of Contents for DCT1800

Reviews:

Related manuals for DCT1800

Brands by name

Popular brands

Motorola DCT1800, Installation Manual

Search results

Summary of Contents for DCT1800

Reviews:

Related manuals for DCT1800

Brands by name

Popular brands