background image

12A

12

EN

06. COMPONENTS TEST

230V/110V MOTOR

01

 • Replace the brown and black wires by white wires and connect in the terminal. 

02

 • Connect the capacitor in the terminal, in the same white wires inputs.

03

 • Connect the power supply wires in the opening the motor will rotate one way and 

during the closing, the motor will rotate the opposite way.

04 

• Finally, connect it to a 230V or 110V plug, depending on the motor/control board in test.

If the motor works

, the problem is in the microswitches.

If the motor does not work, 

normally the problem is on the motor. Replace it with a new 

one and test again.

01 

• Connect the 3 automation wires in the terminal. 

02

 • Connect the two automation white wires with the capacitator wires.

03

 • Connect the power supply wires in the opening the motor will rotate one way and 

during the closing, the motor will rotate the opposite way. 

04

 • Finally, connect it to a 230V or 110V plug, depending on the motor/control board in test.

If the motor works

, the problem is in the control board.

If the motor does not, 

make the 

TEST 2

.

TEST 1

 - Control board Functioning

TEST 2

 - Micros functioning 

Motor

Motor

Motor

Motor

Black

Black

Gray

Gray

Brown

Brown

COM

COM

Power 

Supply

Power 

Supply

Power 

Supply

Power 

Supply

Power 

Supply

Power 

Supply

AUTOMATION

AUTOMATION

Ground Wire

Ground Wire

Ground Wire

Ground Wire

Black

Black

Brown

Brown

Phase

Phase

Gray

Gray

COM

COM

Phase

Phase

Capacitor

12,5μF (230V)

/35μF (110V)

Capacitor

12,5μF (230V)

/35μF (110V)

Capacitor

12,5μF (230V)

/35μF (110V)

OPEN

CLOSE

OPEN

CLOSE

Capacitor

12,5μF (230V)

/35μF (110V)

All tests must be performed by qualified per-

sonnel due to serious danger associated with 

the misuse of electrical systems!!

To detect if the malfunction is on the control board or on the motor 

is, sometimes, necessary to perform tests with connection directly 

to a 110V/230V power supply.

For this, it is necessary to interpose a capacitor on the connection 

in order to the automatism to work (check the type of capacitor to 

be used in the product manual).

The diagram below, shows how to make that connection and how to 

merge the different components wires.

NOTES:

• To perform the tests, there is no need to remove the automatism from 

the place it is installed, because in this way, it is possible to understand if 

the automatism can function properly connected directly to the current.

• You should use a new capacitor during this test to ensure that the pro-

blem does not lie on it.

Summary of Contents for JAG400
















Reviews: