background image

9A

9B

B

A

B

A

17

18

19

20

21

22

23

24

25

26

EN

EN

01

 • Unlock the motor (see page 4A).

02

 • Loosen the 3 front screws, remove the cover and the profile cover.

03 

• Take the gate to the closed position.

04

 • Loosen the screw shown in the image (21), so that it is possible to move the micro-switch in 

the profile.

05

 • Adjust the closure micro-switch (A) until it makes “click” on the pressure piece. Tighten the 

screw to secure the micro in that position.

06

 • Take the gate to the open position.

07

 • Loosen the screw shown in the image (24), so that it is possible to move the micro-switch 

in the profile.

08

 • Adjust the closure micro-switch (B) until it makes *click* on the pressure piece. Tighten the 

screw to secure the micro in that position.

• The Closing Micro-Switch.

• The Opening Micro-Switch.

09

 • Test the door manually and 

if necessary readjust the micros, 

as indicated in the previous 

paragraphs.

10

 • When finished, place the 

profile cover and the plastic 

cover.

11 

• Repeat the whole process 

for the other motor.

04. INSTALLATION

MICROS ADJUSTMENT

04. INSTALLATION

MICROS ADJUSTMENT

Example of the gate with inside opening

Summary of Contents for JAG400
















Reviews: