background image

GARAGE DOORS & OPENERS

Part No.

IMPORTANT NOTICES!

Wayne-Dalton highly recommends that you read and fully  under-
stand the Installation Instructions and Owner’s Manual before you 
attempt this installation. 
To avoid possible injury, read the enclosed instructions carefully  
before installing and operating the garage door. Pay close attention 
to all warnings and notes. After installation is complete, fasten this 
manual near garage door for easy reference.
The complete Installation Instructions and Owner’s Manual are  
available at no charge from:
Wayne-Dalton, a Division Of Overhead Door Corporation, 
P.O. Box 67, Mt. Hope, OH., 44660, 
Or Online At 

www.Wayne-Dalton.com

F

ront

 M

ount

 L

ow

 H

eadrooM

I

n s I d e

 H

o o k

-u

p

MH

InstaLLatIon

 

InstructIons

 

and

 

owner

s

 

ManuaL

t

o r s I o n

8700

T a b l e   O f   C o n t e n t s

347215

REV1 08/22/2011

©Copyright 2011  Wayne-Dalton, a Division Of Overhead Door Corporation

Parts Breakdown 

2

Pre-Installation 

3

Important Safety Instructions 

3

Tools Required 

3

Package Contents 

3

Door Section Identification 

4

Removing an Existing Door 

4

Preparing the Opening 

4

Installation 

6

Optional Installation 

15

Inside Lock 

15

Pull Down Rope 

15

Door Arm Hookup 

15

Maintenance 

16

Cleaning Your Garage Door 

16

Operation and Maintenance 

16

Warranty 

17

Dealer Locator Information 

18

Summary of Contents for 8700



















Reviews: