manualshive.com logo in svg

MOTO GUZZI V85 E4, Service Station Manual

Share
Download
MOTO GUZZI V85 E4 Service Station Manual Download Page 62

•

(1-2) according to main journal diameter on alternator side.

•

(3-4) according to main journal diameter on clutch side.

SELECTING CRANKSHAFT - CRANKCASE BUSHING CLASSES

Crankcase class

Class 1 crankshaft

Class 2 crankshaft

Class 3 crankshaft

Class 4 crankshaft

Class 1

green-green

yellow-yellow

-

-

Class 2

black-black

green-green

-

-

Class 3

-

-

green-green

yellow-yellow

Class 4

-

-

black-black

green-green

Head and timing

Removing the head cover

NOTE

THE OPERATIONS FOR THE REMOVAL OF THE HEAD COVER ARE THE SAME FOR BOTH
SIDES

•

Remove the spark plug cover

•

Disconnect the spark plug tube

•

Remove the blow-by pipe

•

Undo the three fixing screws of the

head cover and remove the gasket

•

Remove the head cover together with

the gaskets

•

Remove the gasket from the head cov-

er

Engine

Engine V85 E4

ENG - 62

Summary of Contents for V85 E4













































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands