background image

SAFETY WARNINGS AND GUIDELINES 

Please read this entire manual before using this device, paying extra attention to these 
safety warnings and guidelines. Please keep this manual in a safe place for future 
reference. 

 

Do not install this device on an unstable surface where it could fall and cause 
either personal injury or damage to the device and/or other equipment. 

 

Do not expose this device to excessive vibration. 

 

This device is intended for indoor use only. 

 

Do not touch the device, the power cord, or any other connected cables with 
wet hands. 

 

If operating this speaker in a humid environment, ensure that no condensation 
occurs. Condensation could cause damage to the speaker cones and could cause 
a short in the amplifier, which in turn could cause fire or severe electric shock. 

 

Do not expose this device to excessively high temperatures. Do not place it in, 
on, or near heat sources, such as a fireplace, stove, radiator, etc. Do not leave it 
in direct sunlight. 

 

Prior to operation, check the unit and power cord for physical damage. Do not 
use if physical damage has occurred. 

 

Before plugging the unit into a power outlet, ensure that the outlet provides the 
same type and level of power required by the device. 

 

This device uses a grounded power cord and requires a ground connection for 
safe operation. Ensure that the power source has a proper ground connection. 
Do not modify the plug or use a "cheater" plug to bypass the ground connection. 

 

Unplug this device from the power source when not in use. 

 

Take care to prevent damage to the power cord. Do not allow it to become 
crimped, pinched, walked on, or become tangled with other cords. Ensure that 
the power cord does not present a tripping hazard. 

 

Never unplug the unit by pulling on the power cord. Always grasp the connector 
head or adapter body. 

 

Ensure that power is turned off and disconnected before making any electrical 
connections. 

Summary of Contents for 18806











Reviews: