background image

TROUBLE SHOOTING TIPS

CAUTION :

  

As failures or errors occur, please use the following table to try 
and fix the device. If the device remains problematic, please send 
back to the manufacturer for repair.

Federal law restricts this device to sale or on the order of a dentist.

DESCRIPTIONS

The red and green 
signal lights of 
charger stand are 
unable to light up

Poor connection 
between plug and 
cable

Check the connection 
between plug and 
cable

LCD device is 
unable to light up

Defect in LCD 
device or pc board

Return to 
manufacturer / agent 
for repair

No activation 

Lithium-ion 
battery is defective

FAILURE                   

CAUSE                        SOLUTION

Return to 
manufacturer / agent 
for repair

Defect in charger

Defect in main IC 
board

LED lamp is unable
to emit

Defect in LED 
module

SPECIFICATION

CURING HANDPIECE :

LED LAMP : 5 Watt.

LIGHT INTENSITY : up to 1,500 mW/cm

WAVE LENGTH : 450 ~ 470 nm

DIMENSION : 18.5(L) x 3.86(W) x 8.2(H) cm

WEIGHT : APPROX. 206g

CHARGER :

OUTPUT VOLTAGE : 8.4 V (TYPICAL)

DIMENSION : 19.3(L) X 8.38(W) X 9.59(H) cm

WEIGHT : APPROX. 177 g

BATTERY :

LI-ION BATTERY PACK : 1 PC

VOLTAGE : 7.4 V (TYPICAL)

CAPACITY : 1,350 mAh (TYPICAL)

DIMENSION :  Approx. 1.8 x 6.5 cm

WEIGHT :  Approx. 78 g

ADAPTOR :

INPUT : AC100 V ~ 240 V  50/60 Hz

OUTPUT : DC 9 V

CURRENT : 1.3 A (TYPICAL)

LIGHT GUIDE :

FIBER OPTIC WITH TAPERED TIP

      10mm taper to    8mm

AUTOCLAVABLE UP TO 134 

°

C

2

E

N

G

L

IS

H

8

9

Summary of Contents for Ti-Lite GT-1500













Reviews: