manualshive.com logo in svg

molex Brad HarshIO 300 ePN, User Manual

Share
Download
molex Brad HarshIO 300 ePN User Manual Download Page 40

 

HarshIO 300 ePN 

 40 

  

IP67 Digital I/O Modules for PROFINET IO 

 

To perform the reset, power on the module with the rotary switches in 
position 900, wait 5 sec and power off the module. The module is now 
configured with the following parameters:   
 
Module factory settings: 
 

PROFINET name 

 

molex-harsh300-ip67 

Rotary switch Position 

700 

IP address:    

 

0.0.0.0  

Subnet mask:  

 

0.0.0.0  

Gateway:    

 

0.0.0.0 

ETH1 port:    

 

Auto negotiation / Auto MDIX 

ETH2 port:    

 

Auto negotiation / Auto MDIX 

LLDP: 

 

 

Enabled 

Easy Replacement:   

Enabled 

 
 

999 

 

Reserved for technical support (firmware download) 
 
 

 
Note: The rotary switch position is ONLY read at the boot of the module. Any modification of the position will 
require a power cycle (ON 

 OFF 

 ON) of the module.   

 
Note: All other rotary switch positions are forbidden. In all of these cases, the HarshIO module will not start 
and the MOD led status will blink in RED. 
 
Note: If a DCP request is received, and the rotary switches are not on DCP mode (position 700), the module 
will reject the request. 
 
 
 
 

 

Summary of Contents for Brad HarshIO 300 ePN

























































Reviews:

No comments

Brands by name

Popular brands

Load more brands