MODULARWALLS Slimwall Classic Post Installation Manual Download Page 13 | Manualshive

Page: 13 / 36

background image

Make sure the base bracket is free of debris. Then with one person at either end, lift the panel vertically and

insert into the top rebates of the post. You may need a small platform to stand on to achieve the required height.
The first panel will have the capping channel installed so the initial part will be tight to insert as the post is trying

to ‘stretch’ to accommodate the panel plus the capping channel, this is normal.

NOTE: The panel must be guided down at an even and level rate or it will jam.

NOTE: Always take special care if working from heights or lifting objects above your head.

STEP 3: PANELS

INSERTING THE WALL PANELS

Slide down evenly

capping channel

INSTALLING ON SLOPING GROUND?

If you are stepping or raking your wall on sloping ground, please refer to

page 20

for specific brackket

instructions.

SLIMWALL™ INSTALLATION GUIDE

13

«
...
11
12
13
14
15
...
»

Summary of Contents for Slimwall Classic Post





































Reviews:

No comments

Related manuals for Slimwall Classic Post

Brand: Fontaine Aquanox Pages: 15

Brand: Automatic Solutions Pages: 2

Brand: Fentec Pages: 12

Bolton 73025736

Brand: Barrette Pages: 7

Brand: Barrette Pages: 10

Brand: RYTEC Pages: 36

Brand: ENCLO Pages: 12

Brand: ENCLO Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands