-
Height 215 cm
-
Installation diameter 260 cm
-
Weight 19.8 kg
Tripod DB OCTOPUS
-
Completely demountable using a plug-in system
-
All legs can be telescoped in 5 stages
-
5 usable attachment eyelets on the tripod head
-
Model with 3 suction cups with ball joint
-
1 set of connection tubes
-
Height 120 – 145 cm
-
Installation diameter 140 cm
-
Weight 18.8 kg
Tripod DB OCTOPUS MINI
-
Completely demountable using a plug-in system
-
All legs can be telescoped in 5 stages
-
5 usable attachment eyelets on the tripod head
-
Model with 3 suction cups with ball joint
-
1 set of connection tubes
-
Height 86 – 114 cm
-
Installation diameter 100 cm
-
Weight 16.9 kg
3 Installation
3.1 Version Tripod DB UNI and DB 500
The tube tops item 1 (position numbers cf. Figure 1) are attached using the lock pin with a yellow anchor eye
item 8 on the tripod head item 9. Insert the tube bottoms item 3 into the tube top item 1 and lock it with a
spring catch item 2. Insert the telescopic foot or the telescopic feet item into the tube bottoms and lock with the
lock pin item 6 and spring catch item 7 in the desired position. Connect the feet of the tripod to the wire cables
item 4. Spread out the tripod until the wire cables item 4 are tensioned. Alternative to the wire cables, the
tripod legs can also be connected with special connection tubes and clamps. With the DB OCTOPUS and DB
OCTOPUS MINI Tripod versions, the connection is made solely with connecting pipes.
A major prerequisite
for the secure function of the anchor device is the safety of the tripod. Uneven surfaces can be compensated for
with the adjustment foot (feet) item 5. To do this, slacken the wire pin item 7, remove the lock pin item 6 and
bring the adjustment tube into the appropriate position. Here a bore in the tube of the adjustment foot must be
flush with the bore in the bottom of the tube. Now insert the lock pin and secure with the wire pin while
pulling outward. When erecting the tripod, it should be ensured that the standing feet are lying flat on the
ground with its standing surface. For the round feet, ensure when erecting that the ball joints are not tensioned.
The ball joints are only to be tensioned when the standing areas of the round feet are lying flat on the ground.
For the tripod DB UNI, the adjustment feet can also be inserted without the tube bottoms directly into the tube
tops and secured with lock pins and wire pins. As a result, the tripod can be used with one half installation
height.
3.2 Version of tripod DB UNI and DB 500
The tube tops item 1 (position numbers cf. Figure 1) are attached using the lock pin with a yellow anchor eye
item 8 on the tripod head item 9. Insert the telescopic foot or the telescopic feet item into the tube bottoms and
lock with the lock pin item 6 and spring catch item 7 in the desired position. Connect the feet of the tripod to
the wire cables item 4. Spread out the tripod until the wire cables item 4 are tensioned. Alternative to the wire
cables, the tripod legs can also be connected with special connection tubes and clamps. A major prerequisite
for the secure function of the anchor device is the safety of the tripod. Uneven surfaces can be compensated for
with the adjustment feet item 5. To do this, slacken the wire pin item 7, remove the lock pin item 6 and bring
the adjustment tube into the appropriate position. Here a bore in the tube of the adjustment foot must be flush
with the bore in the bottom of the tube. Now insert the lock pin and secure with the wire pin while pulling
outward. When erecting the tripod, it should be ensured that the standing feet are lying flat on the ground with
its standing surface. For the round feet, ensure when erecting that the ball joints are not tensioned. The ball
joints are only to be tensioned when the standing areas of the round feet are lying flat on the ground.
