background image

 

A-5

 

 CONTENTS 

 

 

1. Overview........................................................................................................ 1 
2. Performance Specifications ........................................................................... 2 
3. Mounting and Installation ............................................................................... 3 

3.1 Handling Precautions ............................................................................... 3 
3.2 Installation Environment ........................................................................... 3 

4. Part Names.................................................................................................... 4 
5.External Wiring ............................................................................................... 6 

5.1 Connecting to the 10BASE-T/100BASE-TX ............................................. 6 
5.2 Connecting to the RS-232 ........................................................................ 7 

6. Setting from GX Developer ............................................................................ 8 
7. External Dimensions.................................................................................... 11 
8. Transportation Precautions.......................................................................... 12 

8.1 Target Models of Regulations................................................................. 12 
8.2 Transport Guidelines .............................................................................. 12 

 

Summary of Contents for QJ71WS96 Series





















Reviews: