10
1
SETTING THE OPERATION WHEN THE TAPE REACHES THE END (TAPE END)
Sets the state of operation of the VCR when the tape runs out during recording.
STOP:
The tape stops. “End” will appear on the fluorescent display and “Tape End” will appear
on the monitor. When “CALL OUT” is set to “WRNG•TAPE END”, a CALL signal is output
from the CALL terminal.
REWIND: Rewinds the tape to the beginning and stops (except during timer recording.)
When “CALL OUT” is set to “WRNG•TAPE END”, a CALL signal is output for 2 seconds from the CALL terminal.
REPEAT: Rewinds the tape to the beginning and resumes recording.
ALARM•PROT (ALARM PROTECTION): If alarm recordings are present on the tape, then the tape stops. “End” will appear on
the fluorescent display and “Tape End” will display on the monitor. When “CALL OUT” is
set to “WRNG•TAPE END”, a CALL signal is output from the CALL terminal. If there are
no alarm recordings, the tape is rewound and recording continues.
2
SETTING QUASI-V-SYNC (QUASI V-SYNC)
Sets Quasi-V-Sync on or off.
ON:
Quasi-V-Sync signal is inserted on the video output signal when in the special playback modes (still, slow motion,
reverse, fast playback, speed search) and during normal playback in L18H, 72H or 96H mode.
OFF: Quasi-V-Sync signal is not inserted.
N
Some multiplexers may require the Quasi-V-sync OFF in order to work properly.
3
SETTING THE TAPE LENGTH (TAPE LENGTH)
Select the tape length to function the tape remain indicator correctly.
E-180: When using E-180 tape
E-240: When using E-240 tape
4
SETTING THE PRESENT TIME, DATE AND DAYLIGHT SAVING TIME SETTINGS (TIME DATE ADJUST)
Refer to the pages 11 - 12.
FIRST TIME SET UP
1
DISPLAYING THE POWER LOSS LIST (POWER LOSS LIST)
Turn the JOG dial to select “POWER LOSS LIST”. Turn the SHUTTLE ring to the right to display the
Power Loss List. Power failure start times are stored in memory, so it is possible to confirm when
they have occurred. Up to 3 power failure start times will be displayed. If more than 3 failures have
occurred, the first and the last 2 power failure start times will be displayed.
2
DISPLAYING THE ALARM LIST (ALARM LIST)
Turn the JOG dial to select “ALARM LIST”. Turn the SHUTTLE ring to the right to display the Alarm List. Alarm record start times
are stored in memory, so it is possible to confirm when they have occurred. Up to 3 alarm record start times will be displayed. If
more than 3 alarm records have occurred, the first and the last 2 alarm record start times will be displayed.
3
INITIALIZING ALL MENU SETTINGS (ALL MENU INITIALIZE)
Turn the SHUTTLE ring to the right and “ALL MENU INITIALIZE” will be displayed. When the SHUTTLE ring is turned to
the left, each setting is initialized except the TIMER RECORDING setting. When the SHUTTLE ring is turned to the right,
the “MAINTENANCE” menu will be displayed.
4
POWER LOSS LIST CLEAR
Turn the SHUTTLE ring to the right “POWER LOSS LIST CLEAR” will be displayed. When the SHUTTLE ring is turned to the
left, the Power Loss List is cleared. When the SHUTTLE ring is turned to the right, the “MAINTENANCE” menu will be displayed.
5
ALARM LIST CLEAR
Turn the SHUTTLE ring to the right and “ALARM LIST CLEAR” will be displayed. When the SHUTTLE ring is turned to the left,
the alarm list is cleared. When the SHUTTLE ring is turned to the right, the “MAINTENANCE” menu will be displayed.
MAINTENANCE
0
0H
<MAINTENANCE>
POWER LOSS LIST
ALARM LIST
ALL MENU INITIALIZE
POWER LOSS LIST CLEAR
ALARM LIST CLEAR
<
REPEAT REC TIMES
>
<
ELAPSED TIME
>
<
FIRST TIME SET UP
>
TAPE END
QUASI V-SYNC
TAPE LENGTH
TIME DATE ADJUST
STOP
ON
E-180
Summary of Contents for HS-7496E
Page 32: ...872C190D8 PRINTED IN JAPAN ...