Mitsubishi Heavy Industries SC-SL4-AE2 User Manual Download Page 23

Page: 23 / 98

– 22 –

<For Q-ton group (

page 47)>

Press the button for the item to set or change.

• RUN/PAUSE

Press the RUN or PAUSE button.

• HW TEMP.

Set hot water temperature.
Press

page 68 (HOT WATER TEMP LIMIT SETTING)

Lower limit value is 60°C.

• HW AMOUNT

Set hot water storage amount.
Press

• KEEP WARM (only when the tank type is OPEN)

Set keep warm temperature.
Press

Lower limit value

Upper limit value

40°C

63°C

• PEAK-CUT

Set the saving rate of capacity of the heat pump unit.
Set to 0, 40, 60, 80, or 100%.
Press

Note

100% means the peak cut is canceled.

• HEAT TEMP.

Set the heating set temperature.
Press

Lower limit value

Upper limit value

20°C

52°C

• FILL UP

Press the START or FINISH button.

– When the START button is selected,

ll up starts.

– When the FINISH button is selected,

ll up ends.

• SILENT

Press the ON or OFF button.

• ANTI-LEGIONELLA

Press the ON or OFF button.

• HEATING

Press the ON or OFF button.

Summary of Contents for SC-SL4-AE2



































































































Search results

Summary of Contents for SC-SL4-AE2

Reviews:

Related manuals for SC-SL4-AE2

Brands by name

Popular brands

Mitsubishi Heavy Industries SC-SL4-AE2, User Manual

Search results

Summary of Contents for SC-SL4-AE2

Reviews:

Related manuals for SC-SL4-AE2

Brands by name

Popular brands