EN-34
INSTALLATION 1 menu
INSTALLATION 1
LENS LOCK
LENS SHIFT LOCK
ZOOM/FOCUS LOCK
LENS SHIFT RESET
OFF
OFF
COOLING CONDITION
TEST PATTERN
INSTALLATION 1
LAMP MODE
LAMP SELECT
STANDARD
1H/24H
LOW
OFF
STANDARD
0°
DUAL
LAMP RELAY
CROSS HATCH
HIGH ALTITUDE MODE
1
2
STANDBY MODE
IMAGE REVERSE
LENS LOCK
1
1
2
2
opt.
1
1
2
2
opt.
ENTER
OK
ITEM
SETTING
FUNCTION
LAMP MODE
STANDARD
Select this option when you want to view images in a well-lit room.
LOW
Select to moderate the intensity of the lamp. The operating sound is reduced
and the lamp lifetime becomes longer.
LAMP SELECT
DUAL
LAMP 1 and LAMP 2 illuminate.
SINGLE
The lamp with shorter operation time is automatically selected at power-on.
LAMP 1
LAMP 1 illuminates. (When it is broken or dead, LAMP 2 illuminates automatically.)
LAMP 2
LAMP 2 illuminates. (When it is broken or dead, LAMP 1 illuminates automatically.)
LAMP RELAY
DUAL: OFF
The LAMP RELAY doesn’t work.
1H/24H /
2H/1W
Use to set the lamp relay interval. (See page 53.)
SINGLE:OFF
The LAMP RELAY doesn’t work.
24H /
1 WEEK
Use to set the lamp relay interval. (See page 54.)
STANDBY MODE
STANDARD
Select this option when you control the projector via the LAN, REMOTE 1 IN,
and SERIAL OUT terminal during power standby.
LOW
Select this option when you don’t control the projector via the LAN, REMOTE
1 IN, and SERIAL OUT terminal during power standby. This option disables
the LAN, REMOTE 1 IN, and SERIAL OUT terminal and reduces the power
consumption during the power standby.
IMAGE REVERSE
OFF
Select when viewing images from the front with the projector installed on the
floor.
MIRROR
Select when viewing images projected from the behind of the screen with the
projector installed on the floor.
INVERT
Select when viewing images projected from the behind of the screen with the
projector installed on the ceiling.
MIRROR INVERT
Select when viewing images from the front with the projector installed on the
ceiling.
HIGH ALTITUDE MODE
STANDARD
Select this option for normal use.
HIGH ALTITUDE
Select this option for use at an altitude of 2000 to 2700 meters above the sea
level.
COOLING CONDITION
0° / 45° / 90° /
135° / 180° /
225° / 270° /
315°
The cooling condition changes according to the selected projection angle.
(See page 13.)
TEST PATTERN
CROSS HATCH
Select to show the test cross hatch pattern.
WHITE
Select to show the maximum brightness image.
BLACK
Select to show the minimum brightness image.
H. COLOR BARS
The horizontal color bar pattern is displayed.
V. COLOR BARS
The vertical color bar pattern is displayed.
LENS LOCK
ENTER
The LENS LOCK menu is displayed for the following settings.
ZOOM/FOCUS LOCK ON / OFF
Use to enable or cancel the FOCUS LOCK and ZOOM LOCK.
LENS SHIFT LOCK
ON / OFF
Use to enable or cancel the LENS SHIFT LOCK.
LENS SHIFT RESET OK
Use to reset the position of the lens to the factory setting.
• Regardless of the setting of LAMP MODE, the STANDARD lamp mode is activated by default whenever the projector is turned
on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.
• When the lamp mode is switched, the projected image may licker.
• Frequent switching of the lamp mode may damage the lamp.
• When using the projector for a long time, set LAMP RELAY.
• To cancel the test pattern, press any button other than the TEST PATTERN button on the remote control.
• While the lamps are being switched, an icon
is displayed to the right of the INSTALLATION 1 menu bar. While the icon is
being displayed, you cannot set LAMP SELECT and LAMP RELAY.
• After you switch the lamps and the newly selected lamp turns on, you cannot turn off the projector for approx. 1 minute.
Menu operation (continued)
