EN-11
Setting up your projector
Before setting up
Before setting up the projector, check the operating environment.
If the environmental requirements are not satisfied, the projector may break down or fail.
Setup environment
The allowable operating temperature varies depending on the projection angle.
For floor installation (projection angle 0°) and ceiling installation (projection angle 180°): +41°F (+5°C) to +104°F (+40°C)
For installation at other angles:
+41°F (+5°C) to +95°F (+35°C)
For use in the HIGH ALTITUDE mode (see page 13), the allowable operating temperature is +41°F (+5°C) to +95°F
(+35°C), which allows floor installation or ceiling installation only.
Setting up the screen
Install the screen perpendicularly to the projector. If the screen can not be installed in such a way, adjust the
projection angle of the projector. (See page 14.)
• Install the screen and projector so that the projector’s lens is placed at the same height and horizontal position of
the screen center.
• Do not install the screen where it is exposed to direct sunlight or lighting. Light directly relecting on the screen
makes the projected images whitish and hard to view.
Screen size and projection distance
Refer to the following table to determine the screen size and projection distance. (For WD8200U only. For WD8200LU,
see page 75.)
• For the aspect ratio setting, see page 25.
• The igures in the tables are approximate and may be slightly different from the actual measurements.
• The lens shift height and width show distances from the factory default position.
L
L
W1
W1
H1
H2
H
W
L
L
W1
W1
H1
H2
H
W
Center of the lens
Center of the lens
Maximum projection area
Maximum projection area
Front projection
Front projection, ceiling mounting
When the aspect ratio is “FULL”
(Display at 1280 x 800 pixels)
Size of the projected image (16:10)
Projection distance (L)
Lens shift height
Lens shift width
Diagonal size
Width (W)
Height (H)
Shortest (Wide) Longest (Tele) Movement distance (H1) Movement distance (H2) Movement distance (W1)
inch
cm
inch
cm
inch
cm
inch
m
inch
m
inch
cm
inch
cm
inch
cm
40
102
34
86
21
54
58
1.5
80
2.0
10
25
5
12
3
9
60
152
51
129
32
81
88
2.2
121
3.1
15
37
7
17
5
13
80
203
68
172
42
108
118
3.0
162
4.1
19
49
9
23
7
17
100
254
85
215
53
135
148
3.8
203
5.2
24
62
11
29
9
22
150
381
127
323
79
202
224
5.7
306
7.8
36
92
17
43
13
33
200
508
170
431
106
269
299
7.6
408
10.4
49
123
23
58
17
44
250
635
212
538
132
337
375
9.5
-
-
61
154
28
72
21
55
300
762
254
646
159
404
450
11.4
-
-
73
185
34
86
26
65
When the aspect ratio is “NORMAL (FULL)” and 4:3 signal is displayed (Display at 1066 x 800 pixels)
Size of the projected image (4:3)
Projection distance (L)
Lens shift height
Lens shift width
Diagonal size
Width (W)
Height (H)
Shortest (Wide) Longest (Tele) Movement distance (H1) Movement distance (H2) Movement distance (W1)
inch
cm
inch
cm
inch
cm
inch
m
inch
m
inch
cm
inch
cm
inch
cm
40
102
32
81
24
61
65
1.7
90
2.3
11
29
5
12
4
10
60
152
48
122
36
91
100
2.5
137
3.5
17
43
7
18
6
15
80
203
64
163
48
122
134
3.4
183
4.7
23
57
10
25
8
20
100
254
80
203
60
152
168
4.3
230
5.8
28
72
12
31
10
25
150
381
120
305
90
229
254
6.4
346
8.8
42
108
18
46
15
37
200
508
160
406
120
305
339
8.6
-
-
57
144
24
61
19
49
250
635
200
508
150
381
425
10.8
-
-
71
179
30
77
24
62
• Depending on the installation conditions, warm air that is emitted from the exhaust vents may low into the intake
vent, causing the projector to display “TEMPERATURE!!” and then stop projecting images.
