Mitsubishi Electric WD8200LU User Manual Download Page 14

Page: 14 / 78

EN-13

Setting the projector posture

You can select the posture of the projector. Set

COOLING CONDITION in the INSTALLATION 1 menu

according to the posture.

Important:

• Inconsistency between the projector posture and

the menu settings may cause breakdown or failure
of the projector or the lamp.

• When you use the projector in the HIGH ALTITUDE

mode, the selectable projector posture is floor
installation (0°) and ceiling installation (180°) only.

Setting the projection angle

• Set

COOLING CONDITION in the INSTALLATION

1 menu referring to the figure below. The default
setting is 0°.

Straight up

Straight down

Ceiling installation

Floor installation

˚ ± 15˚

90°

270˚ ± 15˚

270°

45˚ ± 30˚

45°

135˚ ± 30˚

135°

315˚ ± 30˚

315°

225˚ ± 30˚

225°

0˚ ± 15˚

0°

180˚ ± 15˚

180°

Angle range

Projection angle setting

(See page 32 for menu setting.)
1. Display the INSTALLATION 1 menu.
2. Select COOLING CONDITION by pressing the





button.

COOLING CONDITION

0°

3. Press the ENTER button.

COOLING CONDITION

0°

4. Select the angle by pressing the





button.

5. Press the ENTER button.

Important:

• If the setting value selected in the menu is

inconsistent with the actual projection angle, the
cooling condition setting dialog appears. In this
case, select the projection angle using the





button and then press the ENTER button.

Setting HIGH ALTITUDE MODE

• Set HIGH ALTITUDE MODE in the INSTALLATION

1 menu according to the altitude at which you use
the projector. The default setting is STANDARD.

• Select STANDARD when using the projector at an

altitude from 0 to 2000 meters.

• Select HIGH ALTITUDE when using the projector at

an altitude from 2000 to 2700 meters.

Important:

• If you select STANDARD when using the projector

at an altitude higher than 2000 meters, the
projector may break down or fail.

• When you use the projector in the HIGH ALTITUDE

mode, only floor installation and ceiling installation
are allowed.

(See page 32 for menu setting.)
1. Display the INSTALLATION 1 menu.
2. Select HIGH ALTITUDE MODE by pressing the





button.

HIGH ALTITUDE MODE

STANDARD

3. Press the ENTER button.

HIGH ALTITUDE MODE

STANDARD

4. Select STANDARD or HIGH ALTITUDE by

pressing the





button.

5. Press the ENTER button.

Setting IMAGE REVERSE

• Set IMAGE REVERSE in the INSTALLATION 1 menu

according to the orientation of the projector. The
default setting is OFF.

• Select OFF for the combination of loor installation

and front projection.

• Select MIRROR INVERT for the combination of

ceiling installation and front projection.

• Select MIRROR for the combination of loor

installation and rear projection.

• Select INVERT for the combination of ceiling

installation and rear projection.

(See page 32 for menu setting.)
1. Display the INSTALLATION 1 menu.
2. Select IMAGE REVERSE by pressing the





button.

OFF

IMAGE REVERSE

3. Select OFF, MIRROR, INVERT or MIRROR INVERT

by pressing the





button.

Setting up your projector (continued)

Summary of Contents for WD8200LU















































































Search results

Summary of Contents for WD8200LU

Reviews:

Related manuals for WD8200LU

Brands by name

Popular brands

Mitsubishi Electric WD8200LU, User Manual

Search results

Summary of Contents for WD8200LU

Reviews:

Related manuals for WD8200LU

Brands by name

Popular brands