Mitsubishi Electric PUZ-HA24NHA1, Service Manual

Page: 82 / 128

82
OCH750A
Function Settings Setting No.
Filter sign 100h
2500h
"Clean the filter" indicator is not displayed
Airflow
Quiet
(Fan speed) Standard
High ceiling
No.of air outlets
4 directions
3 directions
2 directions
Optional high efficiency
Not supported
filter Supported
Vane setting
No vanes (Vane No.3 setting: PLA only)
Vane No.1 setting
Vane No.2 setting
Optional humidifier
Not supported
(PLA only)
Supported
Vane differential setting
No.1 setting (TH5: 75– 82˚F [24 – 28˚C])
in heating mode No.2 setting (Standard, TH5: 82– 90˚F [28 –32 ˚ C ])
(cold wind prevention)
No.3 setting (TH5: 90–100 ˚F [32-38˚C])
Swing
Set temperature in heating
mode (4 degC up)
Fan speed when the
Extra low
heating thermostat is OFF
Stop
Keeping fan speed set by remote controller
Fan speed when the
Keeping fan speed set by remote controller
cooling thermostat is OFF Stop
Detection of abnormality of
Detect
07
(107)
08
(108)
09
(109)
10
(110)
11
(111)
13
(113)
14
(114)
23
(123)
24
(124)
25
(125)
27
(127)
28
(128)
the pipe temperature (P8)
Neglect
1
2
3
1
2
3
1
2
3
1
2
1
2
3
1
2
1
2
3
1
2
1
2
1
2
3
1
2
1
2
Not available Swing
Available Wave airflow
Available
Not available
}
PLA-EA
: Initial setting (Factory setting)
-: Not available
4-Way
cassette
PLA-EA
Ceiling
Suspended
PCA-KA
-
-
-
-
-
Mode No.
Wired remote controller
(RF thermostat)
Cealing
concealed
PEAD-AA
-
-
-
-
-
-
-
-
Refer to
the <Table 5>
below.
-
-
-
-
-
Refer to
the <Table 5>
below.
(2) Functions available when setting the unit number to 01-03 or AL (07 in the case of the IR wireless remote controller)
• When setting functions for an indoor unit in an independent system, set the unit number to 01 referring to
4
setting the
indoor unit number.
• When setting functions for a simultaneous twin indoor unit system, set the unit number to 01 to 03 for each indoor
unit in the case of selecting different functions for each unit referring to
4
setting the indoor unit number.
• When setting the same functions for an entire simultaneous Twin-indoor unit system, set refrigerant address to AL
(07 in the case of the IR wireless remote controller) referring to
4
setting the indoor unit number.
<Table 3> Available functions and settings
External static
pressure
Setting No.
Initial setting
(Factory setting)
35Pa
50Pa
70Pa
100Pa
150Pa
2
3
1
2
3
Mode No. 08 Mode No. 10
1
1
2
2
2
<Table 5> Mode No. 08 and 10
<Table 4> Mode No.11
Setting No. Settings PLA-EA
1 Vane No.3 setting
( Downward position than the standard )
Less smudging
2 Vane No.1 setting Standard
3 Vane No.2 setting
( Upward position than the standard )
Less draft *
* In this setting, the ceiling may be smudged.
PCA-KA
No vane function
Standard
Less draft *
( Upward position than the standard )
12-2. SELECTING FUNCTIONS USING THE REMOTE CONTROLLER
Refer to "15-3. SERVICE MENU" and "15-5. FUNCTION SETTING" when selecting functions.