Mitsubishi Electric PLK-J4040RH Technical Manual Download Page 11

Page: 11 / 60

- 5 -

3-4. Installation of the eye guard

(1) Mount the eye guard (No.1) with screw (No.2) to sewing machine head.

3-5. Installation of the rubber cushion

(1) Screw the adjust foot

(No.2)

in the

direction of “a” arrow and locate the rubber cushion

(No.1)

between

the adjust foot and floor which included in accessory box. For the other three rubber cushions, the

procedure is same.

(2) Screw the adjust foot

(No.2)

in the direction of “b” arrow and adjust the adjust foot height so that the

each hour caster

(No.3)

is to be raised from the floor by several millimeters. After adjustment please

check if there is no inclination about the machine table.

<1>: Eye guard unit

<2>: Screw

<1>

<2>

<3>

<1>: Rubber cushion

<2>: Adjust foot

<3>: Caster

<1>

<2>

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Summary of Contents for PLK-J4040RH





























































Search results

Summary of Contents for PLK-J4040RH

Reviews:

Related manuals for PLK-J4040RH

Brands by name

Popular brands

Mitsubishi Electric PLK-J4040RH, Technical Manual

Search results

Summary of Contents for PLK-J4040RH

Reviews:

Related manuals for PLK-J4040RH

Brands by name

Popular brands