Mitsubishi Electric PLK-J4040RH Technical Manual Download Page 20 | Manualshive

Page: 20 / 60

background image

- 14 -

5-9. Adjustment of the thread tension

(1) Adjust the bobbin thread tension with the thread tension adjusting screw (No.2) on the inner hook

(No.1). The thread tension become loose if turn the thread tension adjusting screw (No.2) to the

counterclockwise, and the thread tension becomes tight if turn it to the clockwise.

5-10. Adjustment of upper thread tension

Adjust the upper thread tension corresponding to the bobbin thread tension. The upper thread tension

becomes tight when tightening the thread tension adjusting nut (No.1) clockwise, and the upper thread

tension becomes loose when loosening the thread tension adjusting nut counterclockwise.

NOTE It is possible to adjust the upper thread tension automatically. Please refer to the instructions

OPERATION PANEL technical manual concerning about [Digital tension].

<1>: Inner hook

<2>: Adjusting screw

<1>: Thread tension adjusting nut

<1>

<2>

<1>

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

«
...
18
19
20
21
22
...
»

Summary of Contents for PLK-J4040RH





























































Reviews:

No comments

Related manuals for PLK-J4040RH

Brand: Janome Pages: 84

Brand: handi quilter Pages: 2

Brand: Tornado Pages: 14

BOS-18 II 56382453

Brand: Clarke Pages: 28

Brand: Clarke Pages: 4

Brand: ServiceMaster Pages: 12

MO-6900G Series

Brand: JUKI Pages: 4

Brand: Singer Pages: 10

Code-a-phone 700

Brand: Ford Pages: 52

Brand: Golden wheel Pages: 14

Fog cooler DNG-100

Brand: Antari Pages: 20

HAKOMATIC B 90 CL

Brand: HAKO Pages: 42

Brand: Euro-Pro Pages: 46

SWEEPER VAC V-036

Brand: Vax Pages: 12

Brand: Innovatech Pages: 25

Brand: Geemarc Pages: 84

Brand: Garden Gear Pages: 16

Brand: JUKI Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands