Mitsubishi Electric PLK-J4040RH Technical Manual Download Page 12

Page: 12 / 60

- 6 -

4. LUBRICATION

CAUTION

(1) Please make sure to turn power switch off before lubricating.

(2) Please pay attention that oil does not get on your skin or in your eyes as it may cause an inflammation.

(3) Please make sure to keep oil out of the reach of children who may drink oil by mistake.

NOTICE Please make sure to lubricate when operating for the first time after the installation. Also, please

make sure to check the amount of oil when the machine has not been used for a long time.

4-1. Filling the oil tank

Pour the oil through the oil hole (No.1) to the oil tank (No.2) on the machine arm. Pour the oil through

the oil hole (No.3) which has machine table to the oil tank (No.4).

Please fill with the oil over level

mark (No.5) of the oil tank.

<2>

<1>

<5>

<3>

<4>

<5>

<1>: Oil hole

<2>: Oil tank

<5>: Level mark

<3>: Oil hole

<4>: Oil tank

<5>: Level mark

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Summary of Contents for PLK-J4040RH





























































Search results

Summary of Contents for PLK-J4040RH

Reviews:

Related manuals for PLK-J4040RH

Brands by name

Popular brands

Mitsubishi Electric PLK-J4040RH, Technical Manual

Search results

Summary of Contents for PLK-J4040RH

Reviews:

Related manuals for PLK-J4040RH

Brands by name

Popular brands