Mitsubishi Electric PLK-J4040RH Technical Manual Download Page 9

Page: 9 / 60

- 3 -

3. INSTALLATION

CAUTION

(1) Please have some specialists, who have enough experience for the sewing machine installations,

install the sewing machine.

(2) Please have a Qualified Electrician perform necessary electric wiring.

(3) Please do not operate until the sewing machine is repaired when any damage or fault is found on the

sewing machine at the installation.

(4) Please do not refurbish the sewing machine.

3-1. Installation of the foot switch

Connect the foot switch to the connector CON L. The foot switch is enclosed in the accessory box.

NOTE Refer to the instructions in the paragraph

“[4] Name of each part, wiring and grounding” in the

CONTROL UNIT technical manual.

CON L Foot switch

From the library of Superior Sewing Machine & Supply LLC - www.supsew.com

Summary of Contents for PLK-J4040RH





























































Search results

Summary of Contents for PLK-J4040RH

Reviews:

Related manuals for PLK-J4040RH

Brands by name

Popular brands

Mitsubishi Electric PLK-J4040RH, Technical Manual

Search results

Summary of Contents for PLK-J4040RH

Reviews:

Related manuals for PLK-J4040RH

Brands by name

Popular brands