manualshive.com logo in svg

Mitsubishi Electric MSC-CA20VB, Service Technical Manual

Share
Download
Mitsubishi Electric MSC-CA20VB Service Technical Manual Download Page 163

163

12-10. DRY OPERATION

12-11. HEAT OPERATION

2. High pressure protection

In HEAT operation the indoor coil thermistor detects the temperature of the indoor heat exchanger. The compressor opera-
tional frequency is controlled to prevent the condensing pressure from increasing excessively.

2. Coil frost prevention

Coil frost prevention is as same as COOL mode. (12-9.2.)

1. Thermostat control

Thermostat is ON or OFF by difference between room temperature and set temperature.

ON                                   -1 

:

or more

OFF                                 less than -1 

:

-1

:

-0.7

:

Room temperature minus 
set temperature (During operation)

Room temperature minus 
set temperature (Initial)

Thermostat 

1. Thermostat control

Thermostat is ON or OFF by difference between room temperature and set temperature.

ON                                   less than 2 

:

OFF                                  2 

:

or more

1.7

:

2

:

Thermostat 

Room temperature minus 
set temperature (Initial)

Room temperature minus 
set temperature (During operation)

OBT06D--6qxp  07.3.2 10:16 AM  Page 163

Summary of Contents for MSC-CA20VB





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands