manualshive.com logo in svg

Mitsubishi Electric MSC-CA20VB, Service Technical Manual

Share
Download
Mitsubishi Electric MSC-CA20VB Service Technical Manual Download Page 161

161

MXZ-2A30VA MXZ-2A40VA MXZ-2A52VA

<Control status>

The control performs when the all the following status are satisfied;
• When one or more indoor units are operating in HEAT mode. (Excluding thermostat OFF)
• When discharge temperature becomes 107

:

or more.

• When it passed 60 minutes or more since the operation has started or the last refrigerant recovery has controlled.

<Control details>

LEV opening of indoor unit not operating is controlled to be 80 pulse.

<Control finish status>

The control finishes either as follows. However, the LEV opening is considered to be 59 pulse.
• When it passed 60 seconds since the control has started.
• When the discharge temperature is 90

:

or less.

12-6. REFRIGERANT RECOVERY CONTROL ON HEATING

This protection controls the compressor ON/OFF and operation frequency according to temperature of the discharge 
temperature thermistor.
(1) Compressor ON/OFF

When temperature of the discharge temperature thermistor exceeds 116

:

, the control stops the compressor.

When temperature of the discharge temperature thermistor is 80

:

(2A/3A/4A71/4A80VA

-

)/ 100°C (4A80VA

-

/5A) or

less, the controls starts the compressor.

(2) Compressor operation frequency

When temperature of the discharge temperature thermistor is expected to be higher than 116

:

, the control decreases 12Hz

from the current frequency.
When temperature of the discharge temperature thermistor is expected to be higher than 111

:

and less than 116

:

, the con-

trol decreases 6Hz from the current frequency.
When temperature of the discharge temperature thermistor is expected to be higher than 104

:

and less than 111

:

, the con-

trol is set at the current frequency.

E2

E1

12-5. DISCHARGE TEMPERATURE PROTECTION CONTROL

Fan speed is switched according to the number of operating indoor unit and the compressor frequency.

12-7. OUTDOOR FAN CONTROL

COOL

Up

Down

Up

Down

Mode

HEAT

Compressor frequency (Hz)

Fan speed

<Relation between compressor frequency and fan speed>

56

42

56

42

Up

Down

Fan speed

High

Low

Compressor frequency

Min.

Max.

40

30

40

30

MXZ-2A40VA-

MXZ-2A52VA
MXZ-3A54VA

MXZ-4A71/80VA-

MXZ-2A30VA

MXZ-2A40VA-

E2

E1

E2

50

40

50

40

MXZ-4A80VA-

MXZ-5A100VA

E1

Note
• When the indoor coil thermistor is 57

:

or more on HEAT operation, fan speed is fixed to Low speed.

Or, the indoor coil thermistor is 45

:

or less on HEAT operation, fan speed is back to normal.

OBT06D--6qxp  07.3.2 10:16 AM  Page 161

Summary of Contents for MSC-CA20VB





































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands