Mitsubishi Electric MR-B42S, Operating Instructions Manual

Page: 26 / 60

26
What to do when...
What to do when ...
Front
Lower
interior
Upper part of
back side
The “FZR”
lamp blinks
about every
10 seconds.
Electric power
goes out
when Follow the instructions below
To set the freezer
to low temperature
freezing
Transporting
the unit
To move the
refrigerator or to
change the direction
The unit will not
be used for a long
period of time
s2EFRAINFROMFREQUENTLYOPENINGANDCLOSINGTHEREFRIGERATORDOORSANDAVOIDSTORINGADDITIONALITEMS
s3ETTINGFORMODESOTHERTHANTEMPERATUREMAYCHANGE0LEASECHECK#HILD,OCK%NERGY3AVING&AST#OOLINGETC
1
Lift adjustable supports
2
Move it in forward and backward directions
$RAGGINGITINDIRECTIONSOTHERTHANTHELONGITUDINALFORWARDANDBACKWARDDIRECTIONSMAYCAUSEDAMAGETOTHEFLOOR
3
Make sure to place a cloth for floor protection underneath the caster and rear support before changing directions.
1
Clean the automatic ice maker.
2
After removing the power plug from the outlet, clean the interior of the unit. Leave the
doors open for 2 to 3 days to sufficiently dry the interior of the unit.
*
&AILURETOSUFFICIENTLYDRYTHEINTERIOROFTHEUNITCANCAUSEMOLDINGODOURSANDREFRIGERANTGAS LEAKAGEDUETOCORROSIONOFTHECONDENSER
page
7
page
22
1
Discard the water and ice in the water tank and the ice tray.
2
Wear the protector such as work-gloves.
3
Remove the leg cover and lift up the adjustable support.
4
Pull out the power supply plug.
5
Throw away water from the evaporating dish.
6
Gently transport the unit with 2 or more people, gripping
the hand-holds on the lower-front interior and the upper-rear
of the unit.
s$ONOTLAYTHEUNITONITSSIDEDOINGSOCANCAUSEMALFUNCTIONOFTHE
COMPRESSOR
page 21
page
24
It uses flammable refrigerant, do not damage the refrigerant circuit. If the gas leaks, ignition or explosion
may be caused.
Warning
1
Press repeatedly until the lamp lights up.
3
Press to set the temperature control to .
Set the temperature control display to any level other than or follow
step
2
above.
*
3ETTHETEMPERATURECONTROLTOTHEFINEADJUSTMENTMODEANDSETTHETEMPERATURECONTROLOFTHEFREEZERTO
4HENTHEREFRIGERATORSETSTHEFREEZERTEMPERATURESLIGHTLYLOWER
2
Press and simultaneously for about
3 seconds. (until the buzzer emits “peep, peep” tone.)
To cancel
How to cancel demonstration operation
s4HEREFRIGERATORSUSPENDSITSCOOLINGFUNCTIONDURINGTHISMODE0LEASECONTACTTHE
RETAILSTOREATWHICHYOUPURCHASEDITFROMORRESETTHEDEMONSTRATIONOPERATIONBYTHE
FOLLOWINGRESETTINGMETHOD
Contact the retail store at which you purchased it
or MITSUBISHI SERVICE CENTER
s0RESSINGh)#%3%,%#4vANDHOLDINGFORABOUTSECONDSWILLSTOPTHEALARMIFITKEEPS
SOUNDING(OWEVERASITISNECESSARYTOPERFORMINSPECTIONPLEASECONTACTTHERETAIL
STOREATWHICHYOUPURCHASEDITOR-)435")3()3%26)#%#%.4%2
All indicators blink 3 times in a constant
interval even though no button has been
pressed. Or, the compartment display
and temperature control display on the
control panel blink in turn repetitively.
(In the demonstration operation mode)
If mark is blinking rapidly
(about 5 times per second)
Or if the alarm cannot be turned off.
1
Keep the refrigerator door open.
2
Press two times.
3
Press , and simultaneously for about 5 seconds.
4
Check that display lamps stop blinking in 1 minute.
4HEDEMONSTRATIONOPERATIONHASNOTBEENCANCELEDIFTHELAMPSREMAINBLINKING