manualshive.com logo in svg

Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series, User Manual

Share
Download
Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series User Manual Download Page 38

36

3  SIGNALS AND WIRING
3.5  Signal (device) explanation

Power supply

Power supply explanations

■

DICOM (Digital input I/F power supply)

Input 24 V DC (24 V DC ± 10 %, 300 mA) for I/O interfaces. The power supply capacity varies depending on the number of I/
O interface points to be used.
For sink interfaces, connect the positive terminal of the 24 V DC external power supply.
For source interfaces, connect the negative terminal of the 24 V DC external power supply.

■

DOCOM (Digital output I/F power supply)

Input 24 V DC (24 V DC ± 10 %, 300 mA) for I/O interfaces. The power supply capacity varies depending on the number of I/
O interface points to be used.
For sink interfaces, connect the negative terminal of the 24 V DC external power supply.
For source interfaces, connect the positive terminal of the 24 V DC external power supply.

■

SD (Shield)

Connect the external conductor of a shielded wire to SD.

Summary of Contents for Melservo-Jet MR-JET G-N1 Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands