manualshive.com logo in svg

Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series, User Manual

Share
Download
Mitsubishi Electric Melservo-Jet MR-JET G-N1 Series User Manual Download Page 108

106

8  USING A LINEAR SERVO MOTOR
8.2  Startup

8.2

Startup

When using a linear servo motor, set [Pr. PA01.1 Operation mode selection] to "4" (Linear servo motor control mode).

Startup procedure

Start up the linear servo system with the following procedure.

*1 Use MR Configurator2.

Installation and wiring

Setting of linear servo motor series and linear servo motor type 

Setting of linear encoder direction and linear servo motor direction 

*1

What is the type of 
the linear encoder?

Incremental linear encoder

Absolute position linear encoder

Linear encoder resolution setting 

*1

Perform the magnetic pole detection. 

*1

Change the setting to disable the 
magnetic pole detection.

Positioning operation check in test operation mode 

*1

Positioning operation check with the controller

Homing operation

Positioning operation

Summary of Contents for Melservo-Jet MR-JET G-N1 Series













































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands