26
Lens of PM2.5 Sensor
1
Remove the cover of the PM2.5 Sensor
.
2
Clean the lens with a dr
y cotton swab.
Do not use water
, alcohol, detergent, etc.
This may cause a malfunction.
3
Attach the cover of the PM2.5 Sensor
.
Cleaning (Cont.)
Approximately Once Ever
y Six Months
When There is an Odor Coming Out of the Air Outlet
Activated charcoal filter
1
Remove the inlet panel, pre-filter
,
and HEP
A filter
.
P.10
2
Remove the activate charcoal filter
.
P.10
3
Soak and wash the activated charcoal filter
.
Soak in cold or lukewarm water for approximately one hour and then wash in water
.
Do not use detergent. Also, do not scrub it. This may cause the activated charcoal filter to become damaged.
4
Allow the activated charcoal filter to d
ry.
Allow them to dr
y properly in a well-ventilated place in the
shade for approximately six hours (the dr
ying time differs
depending on the season and climate).
z
Do not use them while they are still wet.
W
ater drops may be blown from the air outlet and an
odor may be created.
z
Soaking and washing will not completely restore the deodorizing performance of the activated charcoal filter
. Replace this filter when the time for replacement
is reached.
5
Attach the activated charcoal filter to the main unit.
P.
8
6
Attach the HEP
A filter
, pre-filter
, and
inlet panel to the main unit.
P.
8
Replace the filters with new ones when the time for replacement is reached.
Replacement of Filters and Disposal
Replacing the HEP
A filter and activated
charcoal filter
Rough guide on replacement timing
z
When the Replace Filter lamp lights up
The lamp lights up after approximately 4.5 years with “Low” operation or approximately 8 months with “High” operation.
z
When the HEP
A filter becomes ver
y dirty and omits
bad odors
z
When odors cannot be removed from the activated char
coal filter after soaking and washing it
Turn OFF the power switch, disconnect the power plug, and check that the blower fan is stopped before replacing filters.
1
Remove the HEP
A filter and
activated charcoal filter and then install new ones.
P.10
2
Insert the power plug and then reset the Replace Filter lamp.
Press until you hear the “blip, blip blip” sounds (approx. 3 seconds).
z
The Replace Filter lamp goes out. (The lamp is reset.)
z
The life of the HEP
A filter and activated charcoal
filter differs depending on operating environment and conditions of use.
z
When replacing the HEP
A filter
, also replace the
activated char
coal filter at the same time.
z
The HEP
A filter cannot be reused even if it is washed.
When it becomes dirty
, be sure to replace it with a new one.
z
In the following cases, odors may adhere to the HEP
A filter
and main unit. Clean the main unit and replace the HEP
A filter
.
• When a lot of cigarettes are smoked • When there are a lot of odors in the room
Dispose of the filters and main unit in accordance with the local regulations on disposal.
z
HEP
A filter
Materials: PP (polypropylene), rayon, and PET (polyethylene terephthalate)
z
Activated charcoal filter
Materials: Activated char
coal, PET (polyethylene
terephthalate), and PS (polystyrene)
z
Main unit
Dispose of the main unit in accordance with the local regulations on disposal without disassembling it.
Disposal
Consumable parts
z
Replacement filter set
• T
wo-layer HEP
A filter
• Special washable activated char
coal filter (x2)
z
Model
MAPR-865HFT
z
Model code
5D4 820
Purchase from the retail store where you purchased the product.
<When you wish to purchase a filter separately>
When only one of the filters is dirty or damaged or odor cannot be removed from it
z
Replacement two-layer HEP
A filter
z
Ser
vice part number
M25 409 349
z
Replacement special washable activated charcoal filter (x2)
z
Ser
vice part number
M25 409 349K
Purchase from the retail store where you purchased the product. * The sales channels differ so the price of just one filter is relatively high.
Note:
This page is extracted from the full version instruction manual.
