Mitsubishi Electric FR-A8NP Instruction Manual Download Page 15 | Manualshive

Page: 15 / 92

background image

14

INSTALLATION

NOTE

• When mounting/removing the plug-in option, hold the sides of the option. Do not press on the parts on the option

circuit board. Stress applied to the parts by pressing, etc. may cause a failure.

• Caution must be applied to mounting screws falling off when removing and mounting the plug-in option.
• When using this plug-in option, insert it to the inverter option connector 1. If it is inserted to the option connector 2 or 3,

the protective function (E.2 or E.3) is activated and the inverter will not operate.
Even if the option is inserted to the option connector 1, when the inverter cannot recognize that the option is mounted
due to improper installation, etc., the protective function (E.1) is activated.

• When removing the plug-in option, remove the two screws on the left and right, then pull it straight out. Pressure

applied to the connector and to the option board may break the option.

• Always attach the earth plate because a malfunction due to noises may occur without it.

Mounted position

Fault indication

Option connector 1

Option connector 2

Option connector 3

«
...
13
14
15
16
17
...
»

Summary of Contents for FR-A8NP





























































































Reviews:

No comments

Related manuals for FR-A8NP

Brand: Watts Pages: 2

Brand: GE Pages: 425

Brand: Datavideo Pages: 17

Brand: Datamax Pages: 22

Brand: Racal Instruments Pages: 94

Brand: Racal Instruments Pages: 97

Brand: Omegalink Pages: 2

Brand: IBM Pages: 20

Brand: DAV TECH Pages: 24

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 16

Brand: DigiPower Pages: 27

Brand: Mitsubishi Pages: 30

Brand: Lab-T Pages: 17

Brand: Waeco Pages: 168

Brand: Valcom Pages: 9

8040 CNC - FEATURES

Brand: Fagor Pages: 247

Brand: Tate Pages: 32

Brand: Marmitek Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands