Mitsubishi Electric ECODAN EHPX Series Installation Manual Download Page 60

Page: 60 / 64

Service and Maintenance

Error Codes

Code

Error

Action

Circulation water temperature overheat protection

Flow rate may be reduced check for;

• Water leakage

• Strainer blockage

• Water circulation pump function (Error code may display during filling of

primary circuit, complete filling and reset error code.)

DHW tank water temperature overheat protection

Check the immersion heater and it’s contactor.

Indoor unit temperature thermistor (THW1, THW2, THW5, THW6, THW7, THW8,

THW9) failure

Check resistance across the thermistor.

Circulation water freeze protection

See Action for L3.

Heating operation error

Re-attach any thermistors that have become dislodged.

Low primary circuit flow rate detected by flow switch (flow switches 1, 2, 3)

See Action for L3. If the flow switch itself does not work, replace it.

Caution: The pump valves may be hot, please take care.

Boiler circulation water temperature overheat protection

Check if the setting temperature of the Boiler for heating exceeds the re-

striction. (See the manual of the thermistors "PAC-TH011HT-E")

Flow rate of the heating circuit from the boiler may be reduced. Check for

water leakage,

strainer blockage

water circulation pump function.

•

Boiler temperature thermistor (THWB1, THWB2) failure

Check resistance across the thermistor.

Boiler operation error

See Action for L8. Check the status of the boiler.

Boiler circulation water freeze protection

Flow rate of the heating circuit from the boiler may be reduced. Check for

water leakage

strainer blockage

water circulation pump function.

•

Setting errors of Dip switches on FTC4 control board

For boiler operation, check that Dip SW1-1 is set to ON (With Boiler) and

Dip SW2-6 is set to ON (With Mixing Tank).

For 2-zone temperature control, check Dip SW2-7 is set to ON (2-zone)

and Dip SW2-6 is set to ON (With Mixing Tank).

Communication failure between FTC4 and wireless receiver

Check connection cable for damage or lose connections.

Thermistor (Room temp.) (TH1) failure

Check resistance across the thermistor.

Thermistor (Ref. liquid temp.) (TH2) failure

Check resistance across the thermistor.

Anti-freeze protection of plate heat exchanger

See Action for L3.

Check for correct amount of refrigerant.

J1 - J8

Communication failure between wireless receiver and wireless remote controller

Check wireless remote controller’s battery is not flat.

Check the pairing between wireless receiver to wireless remote controller.

Test the wireless communication. (See the manual of wireless system)

E0 - E5

Communication failure between main controller and FTC4

Check connection cable for damage or loose connections.

E6 - EF Communication failure between FTC4 and outdoor unit

Check that the outdoor unit has not been turned off.

Check connection cable for damage or loose connections.

Refer to outdoor unit service manual.

Outdoor unit receives no signal from indoor unit.

Check both units are switched on. Check connection cable for damage or

loose connections. Refer to outdoor unit service manual.

U*, F*

Outdoor unit failure

Refer to outdoor unit service manual.

Note: To cancel error codes please switch system off (Press button E, on Main Controller, for 3 secs).

Summary of Contents for ECODAN EHPX Series

































































Search results

Summary of Contents for ECODAN EHPX Series

Reviews:

Related manuals for ECODAN EHPX Series

Brands by name

Popular brands

Mitsubishi Electric ECODAN EHPX Series, Installation Manual

Search results

Summary of Contents for ECODAN EHPX Series

Reviews:

Related manuals for ECODAN EHPX Series

Brands by name

Popular brands