Mitsubishi Electric ECODAN EHPX Series Installation Manual Download Page 26

Page: 26 / 64

L1
L2

S1
S2

TB1

L2
L3

ECB1

Earth

leakage

circuit

breaker

Outdoor unit

Power

supply

400V

50Hz

Wiring

circuit

breaker or

Isolating

switch

To control

board

For

booster

heater

(Primary circuit)

Hydrobox

Wiring

circuit

breaker or

Isolating

switch

Power

supply

3N~

400V

50Hz

Installation

<3 phase>

Electrical connections 3 phase

Description

Power supply

Capacity

Breaker

Wiring

Booster heater (Primary circuit)

3~ 400V 50Hz

9 kW

16 A *1

2.5 mm²

Wiring

Wiring No. × s

ize

²)

Hydrobox - Outdoor unit

3 × 1.5 (polar)

Hydrobox - Outdoor unit earth

1 × Min. 1.5

Circuit rating

Hydrobox - Outdoor unit S1 - S2

230V AC

Hydrobox - Outdoor unit S2 - S3

24V DC

*1. A breaker with at least 3.0 mm contact separation in each pole shall be provided. Use earth leakage breaker (NV).

The breaker shall be provided to ensure disconnection of all active phase conductors of the supply.

*2. Max. 45 m

If 2.5 mm² used, Max. 50 m

If 2.5 mm² used and S3 separated, Max. 80 m

*3. The values given in the table above are not always measured against the ground value.

Notes: 1. Wiring size must comply with the applicable local and national codes.

2. Indoor unit/outdoor unit connecting cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 60245 IEC 57)

Indoor unit power supply cords shall not be lighter than polychloroprene sheathed flexible cord. (Design 60227 IEC 53)

3. Install an earth longer than other cables.

4. Please keep enough output capacity of power supply for each heater. The lack of the power supply capacity might cause

chattering.

*1 If the installed earth leakage circuit breaker does not have an over-current protection function, install a breaker with that function along the same

power line.

*2 Affix label A that is included with the manuals near each wiring diagram for hydrobox and outdoor units.

Summary of Contents for ECODAN EHPX Series

































































Search results

Summary of Contents for ECODAN EHPX Series

Reviews:

Related manuals for ECODAN EHPX Series

Brands by name

Popular brands

Mitsubishi Electric ECODAN EHPX Series, Installation Manual

Search results

Summary of Contents for ECODAN EHPX Series

Reviews:

Related manuals for ECODAN EHPX Series

Brands by name

Popular brands