- 5 -
Displaying the FUNCTION menu
1. Select “LANGUAGE” in the FEATURE menu.
2. Press the “AUTO POSITION,” “ENTER,” and “AUTO POSITION” buttons on the remote control in order. The FUNCTION
menu will be displayed.
Exiting the FUNCTION menu
Press the “MENU” button while the FUNCTION menu is displayed.
Note:
The menu is not initialized by selecting “RESET ALL” in the FEATURE menu. To initialize the menu, press the “MENU,”
“ENTER,” and “
” buttons of the projector at the same time.
Notes in displaying the FUNCTION menu
When you press the “AUTO POSITION,” “ENTER,” and “AUTO POSITION” buttons with other selection than “LANGUAGE” in
the FEATURE menu, the FUNCTION menu isn’t displayed.
If you continue setting without displaying the FUNCTION menu, you may not be able to display the menus such as the
FEATURE menu and the INSTALLATION menu by the “
” or “
” button. In such cases, press the “MENU” button on the
remote control or that of the projector to exit the current menu, and open the menu again.
Notes in using the FUNCTION menu
- If you change the settings of the WARNING menu after the lamp operating time exceeds 1500 hours, the warning indication
may stay on the screen. In such a case, turn off the power to cancel the warning indication.
- When a test pattern is displayed with [VIDEO] or [S-VIDEO] selected as the input source, subsequent images may not be
displayed correctly. In such cases, select [Computer] as the input source.
FUNCTION MENU (SETTING MENU ONLY FOR SERVICE)
Item
TEST SIGNAL
WHITE, BLACK,
CROSSHATCH,
RED, GREEN,
BLUE, YELLOW,
CYAN, MAGENTA
Function
To display the test patterns.
(The ENTER button displays the test pattern.
Pressing any button cancels the displayed
test pattern.)
OFF
No
A/D LEVEL
±5
To adjust the input gain of A/D to improve solid white
in the image (or too dark image) when the amplitude
of the video signal of the computer is large (or small).
Max.=+10%
Min. =–10%
(every 2%)
0
Yes
MODE DISPLAY
ON,
OFF,
ORIGINAL
To select whether or not to indicate the
switched input terminal in the upper right-hand
corner of the screen at the time of switching
the input terminal while the power is on.
ON: With indication
OFF: Without indication
ORIGINAL: With indication
(High-speed switching)
ON
Yes
To set the time over which the alert for the
lamp replacement is displayed.
LAMP
WARNING1
1 MIN, NO LIMIT
1 MIN: 1 minute
NO LIMIT: No time limit (After the alert is
displayed for one minute, you can cancel
it by any button or RS-232C command.)
1 MIN
Yes
Last
memory
Default
setting
Setting range
DEC LEVEL
±5
To adjust the input gain of DECODER to improve
solid white in the image (or too dark image) when
the amplitude of the video signal is large (or small).
Max.=+10%
Min. =–10%
(every 2%)
0
Yes
C/W DELAY
0 ~ 0359
This item is used when the optical unit is replaced.
Do not change the setting value normally because
it has been uniquely set for each projector.
Improper change will cause incorrect colors.
Unique
value
Yes
To select the remote control sensor to be
enabled.
REMOTE POS.
AUTO, FRONT, REAR
AUTO: Both of FRONT and REAR sensors
FRONT: Front sensor only
REAR: Rear sensor only
AUTO
Yes
Not used normally. To make the gamma
setting linear.
STRAIGHT
GAMMA
ON
Pressing the ENTER button
makes the gamma setting linear.
No
To set the mode to issue lamp replacement
alert.
LAMP
WARNING2
NORMAL,
AFTER P-ON
NORMAL: Alert is displayed every 20
hours after P-ON and 3800-hour of use.
(In the case of the low lamp power mode
operation)
AFTER P-ON: Displayed only after P-ON.
NORMAL
Yes
