15
en
H
A
D
J
A
Main unit
B
Corner of drain pipe
C
Claw on the main unit
D
Grille
1
E
Hole on the grille
F
Hook for temporary installation
G
Screw with captive washer
H
Ceiling surface
J
No gap
K
Adjust the nut of main unit using a wrench,
etc.
Fig. 7-8
Fig. 7-9
Fig. 7-11
Fig. 7-10
Fig. 7-7
Fig. 7-6
F
E
D
A
B
C
C
D
G
K
C
B
A
D
H
E
C
B
G
F
D
A
G
C
F
E
B
A
A
Clamp of the main unit
B
Electrical box
C
Lead wires of the grille
D
CNV connector on the controller board
A
CN4Z on the controller board
B
CN5Y on the controller board
C
Lead wire of i-see Sensor corner panel
D
Clamp
E
Hole of grille (Pass the lead wire.)
F
Screw
3
G
i-see Sensor corner panel
4
< The grille temporary installed >
7.4.2. Temporary installation of the grille (Fig. 7-6)
• Join the corner of drain pipe on the main unit with the corner with hole on the grille
and put them together temporarily by hanging the hook of the grille to the claw of
the main unit.
7.4.3. Fixing the grille
• By tightening the pre-installed screws, fix the grille onto the main unit. (Fig. 7-6)
Note:
Make sure there is no gap between the main unit and the grille or between the
grille and the ceiling surface. (Fig. 7-6)
If there is a gap between the grille and the ceiling:
With the grille attached, slightly adjust the installation height of the main unit and
clear the gap.
Caution:
• When tightening the screw, make sure that the tightening torque is 2.8 N•m
to 3.6 N•m. Never use an impact screw driver.
• After tightening the screw, confirm that the two grille hooks (Fig. 7-7) are
latched onto the hooks on the main unit.
7.4.4. Wire connection (Fig. 7-8)
• Loose the 2 screws fixing the electrical box cover on the main unit, and slide the
cover to open.
• Route the lead wire from side of the electrical box.
• Make sure to connect a connector for vane motor (white, 20 poles) to CNV con
-
nector (white) on the controller board of the main unit.
• Lead wires that lead off the grille must be held together without slack using a clamp
into the electrical box.
7.4.5. Installing signal receiver (Fig. 7-9)
•
Route the lead wire (white, 9 poles) for signal receiver corner panel from the side
of the electrical box on the main unit.
• Make sure to connect to CN90 (white) on the controller board.
• Make sure that the lead wire of the signal receiver corner panel is passed through
the claw of bellmouth.
• The remaining lead wire must be held together without slack using a clamp into
the electrical box.
• Put the cover back on the electrical box with 2 screws.
Note:
Make sure wires are not caught in the electrical box cover.
Install the signal receiver corner panel to the panel and fix with the screw.
The signal receiver corner panel can not be installed on the drain pipe side for the
main unit. (Refer to Fig. 7-11)
A
Signal receiver corner panel
B
Hole of grille (Pass the lead wire.)
C
Claw of bell mouth
D
Wire
E
Clamp
F
Cable band (Secure the lead wire.)
G
CN90 on controller board
H
Screw
7.4.6. Installation of i-see Sensor corner panel (Fig. 7-10)
• Route the lead wire from the side of electrical box.
• Route the lead wire connector (white, 4 poles and white, 5 poles) of the i-see Sen
-
sor corner panel
4
from the side of the electrical box on the main unit and connect
to the connector CN4Z and CN5Y on the controller board.
• The remaining lead wire of i-see Sensor corner panel must be held together without
slack using the clamp into the electrical box.
• Put the cover back on the electrical box with 2 screws.
Note:
Make sure wires are not caught in the electrical box cover.
• The i-see Sensor corner panel should be fixed onto the grille
1
with screw
3
.
* If the position of the i-see Sensor was changed from default position (position
3
)
to the other position, change the function settings. (Fig. 7-11)
• The i-see Sensor corner panel can not installed on the drain pipe side for the main
unit. (Refer to Fig. 7-11)
Position
1
: Default signal receiver position (Air outlet identification marks □/□□□□)
Position
2
: (Air outlet identification marks □/□□)
Position
3
: Default i-see Sensor position (Air outlet identification marks □□/□□□)
Position
1
Position
2
Position
3
Refrigerant pipe
Prohibited installation
position
Drain pipe
7. Installing the grille
RG79F456H01_en.indd 15
2019/07/03 14:25:37
017
017
