Mitel Superset 4025 User Manual Download Page 8

Page: 8 / 49

-4-

CUSTOMIZING YOUR PHONE

Ringer Control

To adjust the Ringer Volume while the phone is ringing:

Press or .

To adjust the Ringer Pitch while the phone is idle:

1. Press

SUPERKEY

2. Press the

softkey until "Ringer Adjust?" appears.

3. Press the

Yes

softkey.

4. Press the

Yes

softkey.

5. Press or to adjust the ringer pitch.
6. Press

SUPERKEY

Handset Receiver Volume Control

To adjust the Handset Receiver Volume when you are using the

handset:

Press or to adjust the handset receiver volume.

Speaker Volume Control

To adjust the Speaker Volume during a Handsfree conversation:

Press or to adjust the speaker volume.

Display Contrast Control

To adjust the Display Contrast while your phone is idle:

Press or to adjust the contrast of the display.

Summary of Contents for Superset 4025


















































Search results

Summary of Contents for Superset 4025

Reviews:

Related manuals for Superset 4025

Brands by name

Popular brands

Mitel Superset 4025, User Manual

Search results

Summary of Contents for Superset 4025

Reviews:

Related manuals for Superset 4025

Brands by name

Popular brands