Mitel Superset 4025 User Manual Download Page 42

Page: 42 / 49

-38-

To park a call and page a call:

1. Answer or make a call.
2. Perform one of the following:

To page all phones and the PA, press

Park & Page Sets

Press

TRANS/CONF

, dial

and dial

To page all phones in a group and the PA, press

Park & Page Grp

Press

TRANS/CONF

, dial

and press

To page an extension number, press

Park & Page

and dial the

extension.
-

Press

TRANS/CONF

, dial

and dial the extension.

To page all phones in a specified group and the PA, press

Park &

Page

and dial the two-digit Page Group Number.

Press

TRANS/CONF

, dial

and dial the two-digit Page Group

Number, then

To park a call in orbit and perform a PA Page to any or all nine Paging
Zones, press

Park & PA Page

and dial the Paging Zone number (0

for all zones, 1-9 for a specific zone).
-

Press

TRANS/CONF

, dial

and dial the Paging Zone number (0 for

all zones, 1-9 for a specific zone)

Note:

To Park and Page call using speed call keys, press

TRANS/CONF

get dial tone before pressing a speed call key programmed with the Park and
Page access codes plus the digits for the required paging option (for
example, an extension number to page a single phone or

to page all

phones plus PA paging).

Summary of Contents for Superset 4025


















































Search results

Summary of Contents for Superset 4025

Reviews:

Related manuals for Superset 4025

Brands by name

Popular brands

Mitel Superset 4025, User Manual

Search results

Summary of Contents for Superset 4025

Reviews:

Related manuals for Superset 4025

Brands by name

Popular brands