manualshive.com logo in svg

Mitel 5760, User Manual

Share
Download
Mitel 5760 User Manual Download Page 5

 

Mitel Networks  5760 VC User’s Guide

v

Regulatory Notices

Note: This equipment has been tested and found to comply with the limits for a 
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio 
frequency energy and, if not installed and used in accordance with the instructions, 
may cause harmful interference to radio communications. However, there is no 
guarantee that interference will not occur in a particular installation. If this 
equipment does cause harmful interference to radio or television reception, which 
can be determined by turning the equipment off and on, the user is encouraged to 
try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which 
the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION

:

To comply with the limits for a Class B digital device, pursuant to Part 15 of the 
FCC Rules, only Mitel Networks 5760 Video Conference Appliance original 
equipment should be used. All cables used to connect the 5760 VC and peripherals 
must be shielded and grounded. Operation with non-certified accessories or non-
shielded cables may result in interference to radio or television reception.

Summary of Contents for 5760



































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands