background image

QMP-5100B and QMP-5101B Installation and Operation Instructions

11

Out of Warranty Repairs 

Mircom Technologies Ltd. will at its option repair or replace out-of-warranty products which are returned to its 
factory according to the following conditions. Anyone returning goods to Mircom Technologies Ltd. must first obtain 
an authorization number. Mircom Technologies Ltd. will not accept any shipment whatsoever for which prior 
authorization has not been obtained. 

Products which Mircom Technologies Ltd. determines to be repairable will be repaired and returned. A set fee which 
Mircom Technologies Ltd. has predetermined and which may be revised from time to time, will be charged for each 
unit repaired. 

Products which Mircom Technologies Ltd. determines not to be repairable will be replaced by the nearest equivalent 
product available at that time. The current market price of the replacement product will be charged for each 
replacement unit. 

The preceding information is accurate as of the date of publishing and is subject to change or revision without prior 
notice at the sole discretion of the Company

WARNING: Mircom Technologies Ltd. recommends that the entire system be completely tested on a regular 
basis. However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical 
disruption, it is possible for this product to fail to perform as expected. 

NOTE:  Under no circumstances shall Mircom Technologies Ltd. be liable for any special, incidental, or 
consequential damages based upon breach of warranty, breach of contract, negligence, strict liability, or 
any other legal theory. Such damages include, but are not limited to, loss of profits, loss of the product or 
any associated equipment, cost of capital, cost of substitute or replacement equipment, facilities or 
services, down time, purchaser’s time, the claims of third parties, including customers, and injury to 
property. 

MIRCOM MAKES NO WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE 
WITH RESPECT TO ITS GOODS DELIVERED, NOR IS THERE ANY OTHER WARRANTY, EXPRESSED OR 
IMPLIED, EXCEPT FOR THE WARRANTY CONTAINED HEREIN.

Summary of Contents for QMP-5100B Series

















Reviews: