background image

-15-

WARRANTY

MIRCOM Technologies Ltd., manufactured equipment is guaranteed to be free of defects in material
and workmanship for a period of one (1) year from the date of original shipment. MIRCOM will repair
or replace, at its option, any equipment which it determines to contain defective material or
workmanship. Said equipment must be shipped to MIRCOM prepaid. Return freight will be prepaid by
MIRCOM. We shall not be responsible to repair or replace equipment which has been repaired by
others, abused, improperly installed, altered or otherwise misused or damaged in any way. Unless
previously contracted by MIRCOM, MIRCOM will assume no responsibility for determining the defective
or operative status at the point of installation, and will accept no liability beyond the repair or
replacement of the product at our factory authorized service depot.

Head Office:

U.S.A. Distribution Centre:

MIRCOM Technologies Ltd.

MIRCOM Technologies Inc.

 25 Interchange Way

60 Industrial Parkway

 Vaughan, Ontario

Cheektowaga, New York

 Canada L4K 5W3

U.S.A. 14227

Telephone: (905) 660-4655

Phone Toll Free: (888) 660-4655

FAX Toll Free: (888) 660-4113

Web Page: http://www.mircom.com

Summary of Contents for FA-1025U





















Reviews: