Mira Advance ATL Installation & User Manual Download Page 20 | Manualshive

Page: 20 / 56

background image

20

Air Bleed

Button

1.15. Make the connection to the mains-

fed cold water supply pipe. Hold a
wrench across the flats of the inlet
connector assembly to prevent
damage to the connector, whilst
tightening the compression nut. Turn
on the water supply.

Priming the Mira Advance ATL
Connect the shower hose to the Mira
Advance ATL and position the hose
to discharge into the shower tray or
bath waste outlet.
Press the air bleed button, located
on top of the flow valve, several
times. This will allow the Mira
Advance ATL to fill with water and
expel any entrapped air.

Note! Failure to prime the unit will
severely effect performance.

Note! Water at full mains supply
pressure will flow from the shower
hose and a small amount of water
will be discharged from under the air
bleed button.

Caution! Once the air bleed button
has been pressed ensure that is
not fouled when released, otherwise
water will continue to discharge from
the bleed button.

«
...
18
19
20
21
22
...
»

Summary of Contents for Advance ATL

























































Reviews:

No comments

Related manuals for Advance ATL

Brand: Gardigo Pages: 9

NAGNODESIGN BDM-REV-410 Series

Brand: Sanipex Pages: 8

BAGNODESIGN BDM-MLI-407 Series

Brand: Sanipex Pages: 8

Brand: Moen Pages: 1

AXOR Urquiola 11026000

Brand: Hans Grohe Pages: 36

Brand: Ideal-Standard Pages: 32

Brand: IB RUBINETTERIE Pages: 16

Brand: Oase Pages: 19

Fasssauna Brage

Brand: Polhus Pages: 25

Croma C 100 3-Jet 04333 0 Series

Brand: Hans Grohe Pages: 12

Brand: PET MARVEL Pages: 6

Sportive 32810003

Brand: Hans Grohe Pages: 8

Enfield Diverter Trim Kit T373430

Brand: American Standard Pages: 1

Brand: Symmons Pages: 3

Brand: Canadian Timber Collection Pages: 41

Brand: baliv Pages: 40

Brand: OVE Pages: 15

Axor Montreux 16520 1 Series

Brand: Hans Grohe Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands