Minuteman M220021H13 Operation & Service Manual Download Page 8

5

ENGINE SET-UP

Refer to Engine Owners Manual for the crankcase oil
capacity.

Single-grade oil is preferable when temperatures are
consistently -over 30

°

F (0

°

C). Multigrade oils are best when

wide temperature variations are anticipated.

 Crankcase pressure can blow out hot

oil, that can cause severe personal injury. Do not check
the oil level while the engine is running.

Excess oil can cause high oil

consumption,  high operating temperatures, and oil
foaming. Do not overfill the crankcase.

    

WARNING

!

     

CAUTION

!

PRE-START CHECKS

Inspect the engine visually. Check for loose or missing parts
and any damage that may have occurred in shipment.

        

        

   Starting the engine without oil will

result in severe engine damage. Add oil prior to starting
the engine.

CRANKCASE OIL RECOMMENDATIONS

Use premium quality motor oil with the API (American
Petroleum Institute) designation SG on the container. Figure
1 shows the recommended oil weight for the temperature
range that the engine will be operated in. Make sure the
engine oil weight is correct for the expected temperature
range.

    

 CAUTION

!

TABLE 1  FIGURE 1

Summary of Contents for M220021H13
























Reviews: