13
12
WALLMOUNT CONFIGURATION
The wallmount configuration
allows the user to mount the UPS on the wall. There is
a wallmount bracket kit available for the UPS. The kit includes two wall mounting
brackets, ten retaining screws, and the wallmount template.
WARNING:
Use two or
more people when installing the UPS, the UPS is extremely heavy. The UPS's side
panels have mounting bracket screw holes for attaching the wall mounting brackets.
1. Once the location of the UPS has been determined, place the UPS on a flat surface
and remove the rackmount brackets from the UPS.
2. The LCD panel can be rotated to read in the up-right position. Remove the front pa-
nel from the UPS. On the backside of the front panel, push the LCD panel outwards,
the panel will pop out. Position the LCD panel so that it reads in the upright position.
Re-install the front panel on the UPS.
WARNING:
The UPS must be installed in the proper up-right position. If the UPS is not
installed in the proper up-right position the Batteries will be damaged. Once the UPS is
placed on the wall, looking at the front panel the YELLOW Battery disconnected label on
the top cover of the UPS MUST be on your left hand side.
3. Align the mounting brackets with the mounting bracket screw holes on the side pan-
els of the UPS and attach with the six retaining screws.
4. Use the template to mark the screw hole position on the wall.
CAUTION
,
you should
always were protective gear for your hands and eyes when operating power tools.
5. Attach the four retaining screws to the wall and make sure that all of the retaining s-
crews are screwed into structural material. Then clean the area of any loose mate-
rial. Do not tighten the retaining screws all the way, leave approximately 3/8" of the
retaining screws sticking out.
6. Position the UPS, so that the mounting bracket keyed holes line up with the four ret-
aining screws. Slide the UPS down until its resting securely on the four retaining s-
crews.
7. Tighten the four retaining screws to secure the UPS to the wall.
8. The Wallmount Configuration is complete. See Connecting your Equipment.
TOWER CONFIGURATION
The tower configuration allows the user to install the UPS in the up-right position
next to a tower computer. The tower brackets are provided with the UPS.
WARNING:
Use two or more people when installing the UPS, the UPS is extremely heavy.
1. Once the location of the UPS has been determined, place the UPS on a flat surface,
remove the rackmount brackets from the UPS and then place the tower brackets in
the desired location.
2. The LCD panel can be rotated to read in the up-right position. Remove the front pa-
nel from the UPS. On the backside of the front panel, push the LCD panel outwards,
the panel will pop out. Position the LCD panel so that it reads in the upright position.
Re-install the front panel on the UPS.
WARNING:
The UPS must be installed in the proper up-right position. If the UPS is not
installed in the proper up-right position the Batteries will be damaged. Once the UPS is
placed in the tower brackets, looking at the front panel the YELLOW Battery discon-
nected label on the top cover of the UPS MUST be on your left hand side.
3. Slide the UPS into the tower brackets. Make sure that the UPS is stable.
4. The Tower Configuration is complete. See Connecting your Equipment.
DESKTOP CONFIGURATION
The desktop configuration allows the user to install the monitor, the computer and
the UPS in one single stack.
WARNING:
Use two or more people when installing the
UPS, the UPS is extremely heavy.
1. Once the location of the UPS has been determined, place the UPS on a flat surface,
remove the rackmount brackets from the UPS and then place the UPS in the desired
location.
2. Stack the computer and then the monitor on top of the UPS.
NOTE:
Do not stack
the UPS on top of the computer. The UPS is heavy and may damage the other equ-
ipment.
3. The Desktop Configuration is complete. See Connecting your Equipment.
