manualshive.com logo in svg

Minarik MMRG Series, User Manual

Share
Download
Minarik MMRG Series User Manual Download Page 24

16

Voltage follower (-PCM models)

PCM series drives can be configured to follow a grounded (non-

isolated) voltage signal.  To configure the drive to follow a voltage

signal, connect the signal leads to the SIGNAL INPUT POS and

SIGNAL INPUT NEG terminals, observing proper polarity.  Note:

There are two locations where signal input connections can be

made, either to terminals TB501 or to the fast-on terminal posts

located below TB501.  (see figure 9, page 17)

Polarity reversal switch (-PCM models)

To reverse the output voltage polarity without changing the input

polarity, connect DIR to COM.  A single-pole, single-throw switch

can be used as a polarity reversal switch.  Close the switch to

reverse the output voltage polarity.  Open the switch to return the

output voltage back to its original polarity.  See Figure 9, page 17

for polarity reversal switch connections.

Installation

Summary of Contents for MMRG Series





























































Reviews:

No comments

Brands by name

Popular brands

Load more brands