Milwaukee MS 304 DB, Original Instructions Manual

Page: 26 / 138

23
GB
TECHNICAL DATA
Mitresaw
MS 304 DB
220 V / 240 V
Production code 4694 15 01 ...
... 000001-999999
Rated input 1800 W
Power input 8 A
No-load speed 3900 min
-1
Saw blade dia. x hole dia 305 x 30 mm
Saw blade thickness 2,4 mm
Cutting width max.
Mitre 0°/ Bevel 0° 102 / 342 mm
Mitre 45°/ Bevel 0° 102 / 241 mm
Mitre 0°/ Bevel 45° 57 / 342 mm
Mitre 0°/ Bevel 45° 45 / 342 mm
Mitre 45°/ Bevel 45° 57 / 241 mm
Mitre 45°/ Bevel 45° 45 / 235 mm
Max. Cutting depth at
Mitre 0°/ Bevel 0°
166 / 53 mm
Mitre 45°/ Bevel 0° 166 / 10 mm
Min. workpiece dimensions 130 x 35 x 2 mm
Weight according EPTA-Procedure 01/2014 29,9 kg
Noise information
Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A))
96,3 dB(A)
Sound power level (Uncertainty K=3dB(A))
Wear ear protectors!
107,3 dB(A)
WARNING Read all safety warnings, instructions,
illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS FOR MITRE SAWS
a) Mitre saws are intended to cut wood or wood-like pro-
ducts, they cannot be used with abrasive cut-off wheels
for cutting ferrous material such as bars, rods, studs, etc.
Abrasive dust causes moving parts such as the lower guard to jam.
Sparks from abrasive cutting will burn the lower guard, the kerf
insert and other plastic parts.
b) Use clamps to support the workpiece whenever
possible. If supporting the workpiece by hand, you must
always keep your hand at least 100 mm from either side
of the saw blade. Do not use this saw to cut pieces that are
too small to be securely clamped or held by hand.
If your
hand is placed too close to the saw blade, there is an increased risk
of injury from blade contact.
c) The workpiece must be stationary and clamped or held
against both the fence and the table. Do not feed the
workpiece into the blade or cut “freehand” in any way.
Unrestrained or moving workpieces could be thrown at high
speeds, causing injury.
d) Push the saw through the workpiece. Do not pull the
saw through the workpiece. To make a cut, raise the saw
head and pull it out over the workpiece without cutting,
start the motor, press the saw head down and push the
saw through the workpiece. Cutting on the pull stroke is
likely to cause the saw blade to climb on top of the workpiece and
violently throw the blade assembly towards the operator.
e) Never cross your hand over the intended line of cutting
either in front or behind the saw blade.
Supporting the
workpiece “cross handed” i.e. holding the workpiece to the
right of the saw blade with your left hand or vice versa is very
dangerous.
f) Do not reach behind the fence with either hand closer
than 100 mm from either side of the saw blade, to remove
wood scraps, or for any other reason while the blade is
spinning. The proximity of the spinning saw blade to your hand
may not be obvious and you may be seriously injured.
g) Inspect your workpiece before cutting. If the workpi-
ece is bowed or warped, clamp it with the outside bowed
face toward the fence. Always make certain that there is
no gap between the workpiece, fence and table along the
line of the cut. Bent or warped workpieces can twist or shift and
may cause binding on the spinning saw blade while cutting. There
should be no nails or foreign objects in the workpiece.
h) Do not use the saw until the table is clear of all tools,
wood scraps, etc., except for the workpiece. Small debris or
loose pieces of wood or other objects that contact the revolving
blade can be thrown with high speed.
English