Milwaukee M18 FUEL SUPER HAWG 2809-20, Operator'S Manual

Page: 4 / 20

4
filter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
No Load Revolutions per
Minute (RPM)
C US
UL Listing Mark pour
Canada et États-unis
SPECIFICATIONS
Cat. No. ..................................................... 2809-20
Cat. No. ......................................................2811-20
Volts .............................................................. 18 DC
Battery Type ................................................. M18™
Charger Type ................................................ M18™
No Load RPM ................... High 0-1550, Low 0-500
Recommended Ambient
Operating Temperature ...................... 0°F to 125°F
Capacities:
Steel
Twist Bit .............................High 5/16", Low 1/2"
Wood
Auger Bit ........................High 1-1/2", Low 1-1/2"
Ship Auger Bit ................High 1-1/2", Low 1-1/2"
Selfeed Bit ...................High 2-9/16", Low 4-5/8"
Hole Saw ...................................High 4", Low 6"
FUNCTIONAL DESCRIPTION
1. Top handle
2. 1/2" Keyed chuck
(Cat. No. 2809-20)
3. LED
4. Chuck key storage
5. Main handle
6. Trigger
7. Control switch
8. 7/16" Hex Quik-Lok ™
chuck (Cat. No. 2811-20)
4
1
2
5
6
8
3
7
ASSEMBLY
WARNING
Recharge only with the charger
specified for the battery. For spe -
cific charging instructions, read the operator’s
manual supplied with your charger and battery.
Removing/Inserting the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
WARNING
Always remove battery pack before
changing or removing accessories.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Only use accessories specifically
recommended for this tool. Others
may be hazardous.
Bit Selection
• Use sharp bits. Sharp bits are less likely to bind
when drilling.
• Use the proper bit for the job. There are many
types of bits designed for specific purposes. Check
the information on the bit's packaging for proper
usage.
• Do not use bits larger than the rated capacity of the
drill. Gear damage or motor overload may result
(see "Specifications").
Installing Bits
Always remove the battery before inserting or remov-
ing bits. Select the proper style and size bit for the
application.
Installing Bits into Keyed Chucks
(Cat. No 2809-20)
1. Remove the battery pack.
2. Open the chuck jaws wide
enough to insert the bit. Be
sure the bit shank and chuck
jaws are clean. Dirt particles
may prevent the bit from lining
up properly.
3. Insert the bit into the chuck.
Center the bit in the chuck
jaws and lift it about 1/16" off of the bottom. Tighten
the chuck jaws by hand to align the bit.
4. Place the chuck key in each of the three holes in
the chuck, turning it clockwise to tighten the chuck
securely.
NOTE: Never use a wrench or means other than
a chuck key to tighten or loosen the chuck.
5. To remove the bit, insert the chuck key into
one of the holes in the chuck and turn it counter-
clockwise.
Installing Bits into 7/16" Hex
QUIK-LOK™
Chuck
(Cat. No 2811-20)
1. Remove the battery pack.
2. To attach an accessory, press the shank into the
hex drive QUIK-LOK™chuck.
3. To remove the accessory, pull out the QUIK-
LOK™chuck ring and remove the accessory.
Release the ring.
Side Handle
The side handle can be installed on either side of the
tool. To install the side handle, thread it into the socket
on the desired side of the tool and tighten it securely.